ISSN 1408-7073 RMZ - MATERIALS AND GEOENVIRONMENT PERIODICAL FOR MINING, METALLURGY AND GEOLOGY RMZ - MATERIALI IN GEOOKOLJE REVIJA ZA RUDARSTVO, METALURGIJO IN GEOLOGIJO RMZ-M&G, Vol. 54, No. 4 pp. 439-577 (2007) Ljubljana, December 2007 Historical Review More than 80 years have passed since in 1919 the University Ljubljana in Slovenia was founded. Technical fields were joint in the School of Engineering that included the Geologic and Mining Division while the Metallurgy Division was established in 1939 only. Today the Departments of Geology, Mining and Geotechnology, Materials and Metallurgy are part of the Faculty of Natural Sciences and Engineering, University of Ljubljana. Before War II the members of the Mining Section together with the Association of Yugoslav Mining and Metallurgy Engineers began to publish the summaries of their research and studies in their technical periodical Rudarski zbornik (Mining Proceedings). Three volumes of Rudarski zbornik (1937, 1938 and 1939) were published. The War interrupted the publication and not until 1952 the first number of the new journal Rudarsko-metalurški zbornik - RMZ (Mining and Metallurgy Quarterly) has been published by the Division of Mining and Metallurgy, University of Ljubljana. Later the journal has been regularly published quarterly by the Departments of Geology, Mining and Geotechnology, Materials and Metallurgy, and the Institute for Mining, Geotech-nology and Environment. On the meeting of the Advisory and the Editorial Board on May 22nd 1998 Rudarsko-metalurški zbornik has been renamed into "RMZ - Materials and Geoenvironment (RMZ -Materiali in Geookolje)" or shortly RMZ - M&G. RMZ - M&G is managed by an international advisory and editorial board and is exchanged with other world-known periodicals. All the papers are reviewed by the corresponding professionals and experts. RMZ - M&G is the only scientific and professional periodical in Slovenia, which is published in the same form nearly 50 years. It incorporates the scientific and professional topics in geology, mining, and geotechnology, in materials and in metallurgy. The wide range of topics inside the geosciences are welcome to be published in the RMZ -Materials and Geoenvironment. Research results in geology, hydrogeology, mining, geotechnology, materials, metallurgy, natural and antropogenic pollution of environment, biogeochemistry are proposed fields of work which the journal will handle. RMZ - M&G is co-issued and co-financed by the Faculty of Natural Sciences and Engineering Ljubljana, and the Institute for Mining, Geotechnology and Environment Ljubljana. In addition it is financially supported also by the Ministry of Higher Education, Science and Technology of Republic of Slovenia. Editor in chief Table of Contents - Kazalo Dissolution of iron in aluminium alloys Raztapljanje železa v aluminijevih zlitinah Kores, S., Vončina, M., Mrvar, P., Medved, J............................................................... 439 The kinetics of precipitation in Al-Mg and Al-Mg-Cu alloy Kinetika izločanja v zlitinah Al-Mg in Al-Mg-Cu Vončina, M., Mrvar, P., Zupanič, F., Medved, J............................................................. 457 Review of materials in medical applications Pregled materialov v medicinskih aplikacijah Bombač, D., Brojan, M., Fajfar, P., Kosel, F., Turk, R................................................ 471 Regional sediment yield pattern for the west flowing rivers of Kerala state, India Chandramohan, T., Balchand, A.N............................................................................... 501 Technology of producing impressed filters to encompass two layers of aquifers Tehnologija izdelave vtisnega filtra v dva paketa vodonosnikov Vukelič, Ž., Lajlar, B., Supovec, I., Vižintin, G........................................................... 513 A realistic estimate of the accuracy of position measurements of characteristic terrain points via the RTK-GPS method Realna ocena natančnosti določanja karakterističnih točk terena po metodi RTK-GPS Vulić, M., Lamot, a....................................................................................................... 529 The use of Leica Geo Office in mine surveying Uporaba programskega paketa Leica Geo Office v jamomerstvu Bilban, G., Vulić, M., Ganić, A..................................................................................... 545 Authors Index, Vol. 54, No. 4 ................................................................................ 557 Authors Index, Vol. 54 ............................................................................................. 558 Contents, Volume 54, 2007/1, 2, 3, 4 ................................................................ 561 Subject Index, Volume 54, 2007/1, 2, 3, 4 ..............................................................................................................564 Instructions to Authors ........................................................................................................................................................................................567 Template ............................................................................................................................................................................................................................................570 No. of indexing of RMZ-M&G in singular Databases Število indeksiranih člankov iz RMZ-M&G v posameznih bazah ................................................................577 Dissolution of iron in aluminium alloys Raztapljanje železa v aluminijevih zlitinah Stanislav Kores 1, Maja Vončina 1, Primož Mrvar 1, Jožef Medved 1 'University of Ljubljana, Faculty of Natural Sciences and Engineering, Department of Materials and Metallurgy, Aškerčeva cesta 12, SI-1000 Ljubljana, Slovenia; E-mail: stanislav.kores@ntf.uni-lj.si, maja.voncina@ntf.uni-lj.si, primoz.mrvar@ntf.uni-lj.si, jozef.medved@ntf.uni-lj.si Received: November 6, 2007 Accepted: December 20, 2007 Abstract: Iron presents in Al-alloys the main impurity, but in some alloys iron presents an alloying element, which increases the hardness of the alloys, but also increases brittleness. In this work the dissolution of iron in electrolytic aluminium and AlSi12Cu(Fe) alloy has been investigated. In experiments iron wire was dissolved in the investigated alloys at temperature 750 °C for 0, 15 and 30 minutes. These specimens were characterized using scanning electron microscope (SEM) and EDS analyzer, in order to determine concentration of iron in the aluminium and to identify iron phases. With the simultaneous thermal analysis (STA) the characteristic temperatures and the solidification, melting and precipitation heats of investigated alloys with dissolved iron were determined. Using the Thermo-Calc simulation program the equilibrium phases were calculated, special emphasis was given to iron phases that form during solidification. Izvleček: Železo predstavlja v aluminijevih zlitinah glavno nečistočo, pri nekaterih zlitinah pa predstavlja zlitinski element, ki povečuje trdoto zlitine in krhkost zlitine. V tem delu se je preiskovalo raztapljanje železa v elektroliznem aluminiju in zlitini AlSi12Cu(Fe). Eksperimentalno je bilo raztapljanje železa opazovano z raztapljanjem železove žičke pri temperaturi 750 °C in času 0, 15 in 30 minut. Vzorci so bili preiskani z vrstičnim elektronskim mikroskopom (SEM) in EDS analizatorjem za določitev koncentracije železa v aluminiju in za definiranje železovih faz. Z uporabo simultane termične analize (STA) so bile definirane karakteristične temperature strjevanja in taljenja ter latentne toplote izločanja preiskovanih zlitin z raztopljenim železom. Z računalniško simulacijo Thermo-Calc so bile izračunane ravnotežne faze, predvsem železove faze, ki se tvorijo pri strjevanju. Key words: Al-alloys, iron dissolution, thermal analysis, thermodynamic equilibrium Ključne besede: aluminijeve zlitine, raztapljanje železa, termična analiza, termodinamično ravnotežje Introduction Iron presents in Al-alloys the main impurity that aggravates ductility and corrosion behaviour. Iron in aluminium is gained from ore, from master alloy or from tools that are used during melting and aluminium casting. Another source of iron in aluminium can be scrap of metallurgical aluminium. In some alloys iron is added as an alloying element to increase hardness; however it also increases the brittleness of the alloys as a side effect. The aim of this work was to determine the dissolution of iron in electrolytic aluminium and AlSi12Cu(Fe) alloy with 0.8 wt.% of Fe. Experiments were carried out in an electrical-resistance furnace at 750 °C. The iron wire was placed into the melt and stayed in it at this temperature over different times. After the preset time the furnace was 1600 1Ю0 O 1S00 1000 eoo 600 m 200 1 1 t 1 1 isr« уу S-— 1 я 11Ù» i/ <уч / 11Я 1041 — ,- . / / N / 6Sf aia - ГЧ - - itti £ > u - 20 ■W 60 go 100 wt.% Pe a) turned off and samples were cooled down to the room temperature. Samples were investigated using a scanning electron microscope (SEM), an EDS analyzer and simultaneous thermal analysis (STA). Equilibrium solidification was calculated by the Thermo-Calc simulation program. Influence of iron concentration in Al-alloys on solidification process For the study of aluminium alloys, where iron is the main alloying element the equilibrium phase diagram Al-Fe, which is presented in Figure 1 was used[1]. Solubility of iron in solid aluminium is very low and amounts 0.04 wt.% at 625 °C [1]. When concentration of iron exceeds 10 wt.% in the system Al-Fe, a peritectic 1400 1200 О 1—. 1000 800 600 400 10 20 30 Лс "Г" ] L 117 у н/ m _JL J 11: W C4. : f L +AI,F e ММ) Ali Fe,-j : _v * : Al, ! I at, % Al 10 20 30 40 Fe, % wt.% Fe b) Figure 1. Equilibrium phase diagram Al-Fe (a) and the aluminium-rich corner (b)[1] Slika 1. Ravnotežni fazni diagram Al-Fe (a) in njegov aluminijev kot (b)[1] reaction L + Al5Fe2 ^ Al3Fe takes places at temperature 1158 °C, which causes formation of Al3Fe phase, which contain 40.7 wt.% Fe (Figure 1). This phase appears in microstructure in the form of needlelike crystals and is fragile and unwished[1]. In Al-Si casting alloys in addition to ß-Al5FeSi phase numerous other phases can be present[2]. In Figure 2 the aluminium corner of ternary phase system Al-Fe-Si is presented[3]. Depending on chemical composition and solidification conditions in microstructure of Al-Si casting alloys the following intermetallic phases could be observed: a-Al8Fe2Si, ß-Al5FeSi and 5-Al9FeSi2 as 8 wt.% Si Figure 2. The aluminium corner of the ternary system Al-Fe-Si [3] Slika 2. Aluminijev kot ternarnega sistema Al-Fe-Si [3] Table 1. Binary and multi-component phases containing iron in Al-Si cast alloys[2] Tabela 1. Binarne in večkomponentne spojine z železom v Al-Si zlitinah[2] Phase Chemical composition (wt.%) Al^ (A^Fe) Fe: 33.9-37.8; Si: 0.8-2.9 Fe: 25.6-28.0 ß-Al5FeSi Fe: 23.5-30.0; Si 12.0-18.9 ß-Al45FeSi (Al9Fe2SÌ2) Fe: 27.0-28.0; Si 14.0-15.0 Y-Al3FeSi Fe: 33.0-38.0, Si: 13.0-18.5 S-Al9FeSi3 Fe: 15.0-25.4; Si: 20.0-25.5 a-Al8Fe2Si Fe: 28.2-31.6; Si: 7.9-10.5 Al9Fe0.84Mn2,16Si Fe: 10.7; Si: 6.44; Mn: 27.2 n-Al8Si6Mg3Fe Fe: 8.0; Si: 25.0-33.8; Mg:13.0-16.0 a-Al12-15(Fe,Mn,Me)3Si1-2, Me=((C1r,Cu) Fe: 8.6-30.7; Si: 4.5-12.5; Mn: 0.52-14.0; Cu: from 7.5, Cr: to 14.4 a-Al^F^Me^Si^, Me=(Mn,Cr,Cu,Co,Ni) Fe: 6.3-25.2; Si: 4.6-10.0; Mn: to 13.1; Cu: to 13.0, Cr: to 14.4; Co: to 20.1; Ni: to 26.8 Al19Fe4MnSi2 Fe: 19.2; Si: 8.3; Mn: 7.8; Cu:2.5; Cr: 0.2 primary crystallized phases. Most often precipitated phase in Al-Si casting alloys is ß-Al5FeSi phase. Table 1 shows typical binary and multi-component phases with iron and other alloying elements in Al-Si castings alloys. Experimental work Iron dissolution was investigated in molten electrolytic aluminium and AlSi12Cu(Fe) alloy. Chemical compositions of investigated alloys are shown in Table 2. Samples were melted in an electrical-resistance furnace in a graphite crucible. When the temperature of the melt reached 750 °C, iron wire was placed into the melt in the middle of the crucible (Figure 3). Dissolution of iron wire was observed at temperature 750 °C for 0 min, 15 min in 30 min. After these preset times the furnace was turned off. The cooling was continued down to the room temperature. The samples were cut into two halves next to the iron wire (Figure 4). The samples were investigated using a scanning Table 2. Chemical composition of investigated alloys in wt.% Tabela 2. Kemijska sestava preiskovanih zlitin v mas.% si fe cu mn mg zn ti al Electrolytic Al 0.041 0.1497 <0.0008 <0.0001 0.0011 0.0089 0.0001 rest AlSi12Cu(Fe) alloy 11.5584 0.8292 0.7159 0.1915 0.0546 0.4673 0.0466 rest Thermocouple typ s K Fe-wirt Graphite crucible Regulator \ \ X Elte tri с -re s is rane t F urn ас с Figure 3. Scheme of the experimental set-up Slika 3. Shema eksperimentalne naprave Figure 4. Scheme of a cut sample and analysed places Slika 4. Shema razreza vzorca s prikazanimi analiziranimi mesti electron microscope (SEM) JEOL JSM-5610. They were prepared by the standard metallographic procedure. The samples were analysed at sites shown in Figure 4. On the basis of iron analysis in Al and AlSi12Cu(Fe) a diagram, iron concentration versus distance from the iron wire was constructed. AlSi12Cu(Fe) samples were researched with simultaneous thermal analysis (STA) on the STA 449 NETZSCH apparatus. The specimens were heated to 720 °C with heating rate of 10 K/min in an argon protective atmosphere and cooled with the same rate down to the room temperature. With computer simulation Thermo-Calc were defined existence of thermodynamic equilibrium phases in electrolytic aluminium and AlSi12Cu(Fe) alloy with 0.8 wt.% Fe. The aim was to determine which iron phases may form during solidification. tical cross-section through Al-corner with variable contents of Al and Fe (a) and Si (b), and constant contents of all other element was constructed (Figure 5). Graphs show that during solidification in Al-Fe system Al13Fe phase precipitate and in Al-Si system ß-AlFeSi phase precipitate. Figure 6 a) presents a concentration of iron in dependence from the distance from the iron wire at temperature 750 °C. The dissolution time was 30 min. It also shows the microstructure of interface between iron wire and aluminium, and at the distances 3 mm and 9 mm from the iron wire. In Figure 6 b) the interface between iron wire and aluminium could be seen, and also the needles of iron phases. It is assumed that this is Al13Fe4 phase, formed during peritectic reaction between the electrolytic aluminium and the iron wire. Concentration of iron in aluminium decreased to 0.5 wt.% Fe at distance 3 mm from iron wire. Results and discussion Using computer simulation Thermo-Calc the existence of thermodynamic equilibrium phases in electrolytic aluminium and AlSi12Cu(Fe) alloy were calculated. Then the equilibrium isoplet phase diagram: ver- Figure 7 a) presents a concentration of iron in dependence from distance from iron wire at temperature 750 °C in electrolytic aluminium. The dissolution time was 15 min. Microstructures on distance b) 1 , c) 3 and d) 9 mm from the iron wire are shown on Figure 7. Needles of iron phases are barely visible, interface between iron wire Figure 5. Equilibrium isoplet phase diagram of electrolytic aluminium with belonging microstructure of Al13Fe4 phase (a) and AlSi12Cu(Fe) alloy with belonging microstructure of AlFeSi-ß phase (b) Slika 5. Ravnotežni izopletni fazni diagram za elektrolizni aluminij s pripadajočimi mikrostrukturnimi fazami Al13Fe4 (a) in zlitino AlSi12Cu(Fe) s pripadajočimi mikrostrukturami faze AlFeSi-ß (b) and aluminium is not shown, concentrati- needles of iron phases are barely visible. on of iron in aluminium decreased to 0.8 Microstructure presents iron phases at the wt.% at distance 1 mm. distance 1, 3 in 9 mm from iron wire. Figure 8 a) presents a concentration of iron in dependence from distance from iron wire at temperature 750 °C in electrolytic aluminium. The dissolution time was 0 min. When the temperature of melt reached 750 °C, the iron wire was placed in the melt and the heating was turned off. On microstructure the interface between iron wire and aluminium is not present and Microstructures were made also on AlSi12Cu(Fe) alloy, which is shown by Figures 9-11. Figure 9 a) presents concentration of iron in dependence from distance from iron wire at temperature 750 °C and dissolution time of 30 min in AlSi12Cu(Fe) alloy. Shown are also microstructures of interface b) between iron wire and aluminium alloy, and on the Dissolving of Fe-w ire in electro lytic aluminium b) C) d) Figure 6. a) Concentration of iron in electrolytic aluminium at different distances from the iron wire (the results of EDS analyses). Scanning electron micrographs (BSE) at different distances from the iron wire after 30 min dissolution time at 750 °C: b) at the interface iron wire - electrolytic aluminium, c) 3 mm and d) 9 mm from the interface. Slika 6. a) Koncentracija železa v elektroliznem aluminiju pri različnih razdaljah od železove žičke (rezultati EDS analize). Posnetki elektronskega mikroskopa (odbiti elektroni) pri različnih razdaljah od železove žičke po 30 min raztapljanja pri 750 °C: b) na prehodu železova žička - elektrolizni aluminij, c) 3 mm in d) 9 mm od prehoda. b) c) d) Figure 7. a) Concentration of iron in electrolytic aluminium at different distance from iron wire (the results of EDS analyses). Scanning electron micrographs (BSE) at different distances from the iron wire after 15 min dissolution time at 750 °C: b) 1 mm, c) 3 mm and d) 9 mm from the iron wire. Slika 7. a) Koncentracijski železa v elektroliznem aluminiju pri različnih razdaljah od železove žičke (rezultati EDS analize). Posnetki elektronskega mikroskopa (odbiti elektroni) pri različnih razdaljah od železove žičke po 15 min raztapljanja pri 750 °C: b) 1 mm, c) 3 mm in d) 9 mm od železove žičke. Figure 8. a) Concentration of iron in electrolytic aluminium at different distance from iron wire (the results of EDS analyses). Scanning electron micrographs (BSE) at different distances from the iron wire after 0 min dissolution time at 750 °C: b) 1mm, c) 3 mm and d) 9 mm from the iron wire. Slika 8. a) Koncentracijski železa v elektroliznem aluminiju pri različnih razdaljah od železove žičke (rezultati EDS analize). Posnetki elektronskega mikroskopa (odbiti elektroni) pri različnih razdaljah od železove žičke po 0 min raztapljanja pri 750 °C: b) 1mm, c) 3mm in d) 9mm od železove žičke. Figure 9. a) Concentration of iron in AlSi12Cu(Fe) alloy at different distances from the iron wire (the results of EDS analyses). Scanning electron micrographs (BSE) at different distances from the iron wire after 30 min dissolution time at 750 °C: b) at the interface iron wire - AlSi12Cu(Fe) alloy, c) 3 mm and d) 9mm from the interface. Slika 9. a) Koncentracija železa v zlitini AlSi12Cu(Fe) pri različnih razdaljah od železove žičke (rezultati EDS analize). Posnetki elektronskega mikroskopa (odbiti elektroni) pri različnih razdaljah od železove žičke po 30 min raztapljanja pri 750 °C: b) na prehodu železova žička - zlitina AlSi12Cu(Fe), c) 3 mm in d) 9 mm od prehoda. Figure 10. a) Concentration of iron in AlSi12Cu(Fe) alloy at different distances from the iron wire (the results of EDS analyses). Scanning electron micrographs (BSE) at different distances from the iron wire after 15 min dissolution time at 750 °C: b) at the interface iron wire - AlSi12Cu(Fe) alloy, c) 3 mm and d) 9 mm from the interface. Slika 10. a) Koncentracija železa v zlitini AlSi12Cu(Fe) pri različnih razdaljah od železove žičke (rezultati EDS analize). Posnetki elektronskega mikroskopa (odbiti elektroni) pri različnih razdaljah od železove žičke po 15 min raztapljanja pri 750 °C: b) na prehodu železova žička - zlitina AlSi12Cu(Fe), c) 3 mm in d) 9 mm od prehoda. b) C) Figure 11. a) Concentration of iron in AlSi12Cu(Fe) alloy at different distances from the iron wire (the results of EDS analyses). Scanning electron micrographs (BSE) at different distances from the iron wire after 0 min dissolution time at 750 °C: b) at the interface iron wire - AlSi12Cu(Fe) alloy, c) 3 mm and d) 9 mm from the interface. Slika 11. a) Koncentracija železa v zlitini AlSi12Cu(Fe) pri različnih razdaljah od železove žičke (rezultati EDS analize). Posnetki elektronskega mikroskopa (odbiti elektroni) pri različnih razdaljah od železove žičke po 0 min raztapljanja pri 750 °C: b) na prehodu železova žička - zlitina AlSi12Cu(Fe), c) 3 mm in d) 9 mm od prehoda. distance 3mm c) and 9 mm d) from iron wire. Dissolving iron combines with Al and Si and forms ß-AlFeSi phase. Interface between iron wire and aluminium alloys is not present as by electrolytic aluminium. Concentration of iron in aluminium alloy decreased to 0.3 wt.% at the distance 1 mm from iron wire. Figure 10 presents concentration of iron in dependence from distance from iron wire at temperature 750 °C and dissolution time of 15 min in AlSi12Cu(Fe) alloy. Shown are also microstructures of interface between iron wire and aluminium alloy, and at the distance 3 mm and 9 mm from iron wire. Interface between iron wire and aluminium alloys, and needles from iron wire are not visible. Concentration of iron in aluminium alloy decreased to 0.2 wt.% at distance 3 mm from iron wire. Figure 11 presents concentration of iron in dependence from distance from iron wire in AlSi12Cu(Fe) alloy and dissolution time of 0 min, which was heated up to 750 °C. Shown are also microstructures of interface between iron wire and aluminium alloy, and on the distance of 3 mm and 9 mm from iron wire. When the temperature of the melt reached 750 °C, the iron wire was placed into the melt and the heating was turned off. Interface between iron wire and aluminium alloy is seen on microstructures. The concentration of iron in alloy varies between 0.2 and 2 wt.% of iron. For samples of AlSi12Cu(Fe) alloy with iron wires was made simultaneous thermal analysis. Figure 12 and 13 presents comparison between heating curves of investigated AlSi12Cu(Fe) alloy and heat of fusion. Notice that with increasing dissolution time of iron wire in melt at 750 °C, the liquidus temperature decreased and eutectic temperature increased. This can be a consequence of increasing iron concentration in the alloy. Comparison of solidus temperatures and their heats of fusion is presented in Table 3. With the simultaneous thermal analysis were measured temperatures of precipitation and the heats of fusion. From diagram on Figures 6 is shown that at specified temperature AlCu-9 is precipitated. The curves in Figure 14 can show that increasing dissolution time of iron wire in the melt at 750 °C, the precipitation temperature and therefore heats of fusion decreased. Comparison of precipitation temperatures and heats of fusion are presented in Table 4. Figure 15 compares cooling curves after different dissolution times of iron wire in AlSi12Cu(Fe) alloy. The curves show that the temperature of primary solidification and temperature of eutectic solidification are similar. The longer is the dissolution time of the iron wire in the melt at 750 °C, less heat is released during solidification. Table 5 shows temperatures of primary solidification, eutectic solidification and heats of fusion. DSCtfrmigl two ■0 i -10 ■J C •315 1 Jg J314-VS, ! -J? ■ г «3 l*C 5511'C \\ III ewa-c \ / \ " \ j $I0&*C 0 min 15 min 30 min KosjossoswwoeocsMMOÈtì) TefuwratirerC Figure 12. Comparison of heating curves of investigated samples in the AlSi12Cu(Fe) alloy Slika 12. Primerjava segrevalnih krivulj preiskovanih vzorcev v zlitini AlSi12Cu(Fe) Table 3. Comparison of melting temperatures and their heats of fusion Tabela 3. Primerjava temperatur začetka taljenja in latentnih toplot, ki se porabijo pri taljenju DISSOLUTION TIME 0 MIN 15 MIN 30 MIN T solidus 551.1 °C 549.1 °C 541.6 °C T eutectic 604.8 °C 610.8 °C 612.6 °C Heat of fusion 358.2 J/g 321.4 J/g 315.1 J/g Table 4. Segregation temperatures for AlCu-0 phase and their latent heats after different dissolution times of iron wire in AlSi12Cu(Fe) alloy Tabela 4. Primerjava temperatur izločanja za fazo AlCu-0 in njihovih latentnih toplot po različnih časih raztapljanja železove žičke v zlitini AlSi12Cu(Fe) dissolution time 0 MIN 15 MIN 30 MIN ^segregation 261.4 °C 235.5 °C 237.5 °C Precipitation heat 8.739 J/g 6.337 J/g 5.737 J/g Figure 13. Melting temperatures and heats of fusion depending on dissolution time of iron wire in AlSi12Cu(Fe) Slika 13. Temperature taljenja in porabljena latentna toplota v odvisnosti od časa raztapljanja Fe-žičke v zlitini AlSi12Cu(Fe) Figure 14. Comparison of cooling curves after different dissolution times of iron wire in AlSi12Cu(Fe) alloy in the temperature region, where precipitation of AlCu-0 phase is expected. The latent heats of precipitation are also given. Slika 14. Primerjava ohlajevalnih krivulj po različnih časih raztapljanja železove žičke v zlitini AlSi12Cu(Fe) v temperaturnem območju, kjer se pričakuje izločanje faze AlCu-0. Podane se tudi latentne toplote izločanja. OSC лгмлипд] 410 440 440 450 WO WO МО МО S8Q 400 Т»гтр»г««1»»ГС Figure 15. Cooling curves after different dissolution times of iron wire in AlSi12Cu(Fe) alloy and corresponding heats of fusion (solidification) Slika 15. Ohlajevalne krivulje po različnih časih raztapljanja železove žičke v zlitini AlSi12Cu(Fe) ter pripadajoče latentne toplote Table 5. Temperatures of primary solidification, eutectic solidification and heats of fusion (solidification) after different dissolution times of iron wire in AlSi12Cu(Fe) melt Tabela 5. Temperature začetka strjevanja, strjevanja evtektika in latentnih toplot, po različnih časih raztapljanja železove žičke v talini zlitine AlSi12Cu(Fe) DISSOLUTION TIME 0 MIN 15 MIN 30 MIN T liquidus 574.9 °C 574.8 °C 574.8 °C T eutectic 559.7 °C 559.7 °C 559.2 °C Heat of fusion 376.8 J/g 337.6 J/g 331 J/g Conclusions The purpose of experiments was to determine of iron dissolution in electrolytic aluminium and in AlSi12Cu(Fe) alloy. According to the results the following conclusions can be drawn: - In Al-Fe system most often iron phase Al13Fe4 is present. In AlSi12Cu(Fe) alloy ß-AlFeSi phase crystallized as a primary phase, in which most of the iron from Fe-wire is present. - The highest concentration of iron in electrolytic aluminium is obtained after dissolution iron wire for 30 min at 750 °C. Iron concentration diagram becomes apparently constant 4 mm from Fe- wire, when the content of Fe in aluminium decreased to 0.5 wt.% Fe. - Concentration profile of dissolving iron in Al-Si alloy is different probably due to binding of iron from iron wire in the primary solidified ß-AlFeSi phase. Concentration of Fe in AlSi12Cu(Fe) alloy drops to 0.3 wt.% Fe at distance 1 mm from iron wire after 30 min dissolution time at 750 °C. - With the help of simultaneous thermal analysis we can claim that by increasing concentration of iron in alloy the solidus temperature decreased and eu-tectic temperature increased. - By increasing the concentration of iron the latent heat for melting (heat of fusion) decreased. Iron phases released less heat during solidification, which was proven by simultaneous thermal analysis. - By increasing concentration of iron in alloy the temperature for precipitation of AlCu-9 phase and amount of released latent heat were decreased. Povzetek Raztapljanje železa v aluminijevih zlitinah Železo predstavlja v aluminijevih zlitinah glavno nečistočo. Pri nekaterih aluminijevih zlitinah pa je glavni zlitinski element, ki izboljša trdoto zlitine, vendar s tem poveča krhkost. V tem delu smo preiskovali kako se železo raztaplja v elektroliznem aluminiju in zlitini AlSi12Cu(Fe). Raztapljanje železa smo preiskovali z vstavljanjem Fe-žičke v elektrolizni aluminij in zlitino AlSi12Cu(Fe), pri temperaturi 750 °C in različnih časih raztapljanja: 0, 15 in 30 minut. Ko je talina dosegla temperaturo 750 °C, smo vanj vstavili železovo žičko in jo pri tej temperaturi držali v talini različno dolgo. Nato smo vzorce razrezali tik ob žički in jih preiskali z vrstičnim elektronskim mikroskopom (SEM), kjer smo ugotavljali koncentracijo Fe v aluminiju in aluminijevi zlitini ter katere železove faze se izločajo. Z računalniško simulacijo Thermo-Calc smo ugotovili, da se v sistemu AlFe pri strjevanju elektroliznega aluminija izloča faza Al13Fe4 pri zlitini AlSi12Cu(Fe) pa faza AlFeSi-ß. Z elektronskim mikroskopom smo analizirali železovo žičko, in vsak milimeter vstran od železove žičke ter naredili posnetek. Nato smo izdelali koncentracijski diagram koncentracije železa v odvisnosti od oddaljenosti žičke. S simultano termično analizo (STA) smo določali karakteristične temperature in toplote taljenja, strjevanja in izločanja. Opazili smo, da dlje kot smo držali Fe-žičko pri 750 °C, nižje so likvidus temperature in višje so temperature taljenja evtektika, kar je posledica povečanja deleža železa v zlitini. Prav tako lahko rečemo, da dlje ko smo žičko držali pri temperaturi 750 °C, nižjo temperaturo izločanja faze AlCu-9 smo dobili in s tem tudi nižje toplote. Iz ohlajevalnih krivulj simultane termične analize pa je razvidno, da dlje kot smo Fe-žičko držali na temperaturi 750 °C v talini, manj toplote se sprosti pri strjevanju. References [1] Belov, N.A., Aksenov, A.A., Eskin, D.G. (2002): Iron in Aluminum Alloys: Impurity and Alloying Element. London and New York, pp. 3-7. [2] Markoli, B., Spaič, S., Zupanič, F. (2004): The intermetallic phases containing transition elements in common Al-Si cast alloys. Aluminium.; Vol. 80, No. pp. 84-88. [3] Massalski, T.B. (1990): Binary Allo- ys Phase Diagrams. 2nd ed., ASM, Metals Park, Ohio. Najpogostejša faza, ki se pojavlja v sistemu aluminij-železo je faza Al13Fe4. V Al-Si zlitinah lahko srečamo številne železove intermetalne spojine, kar je odvisno od kemijske sestave in pogojev strjevanja. Najpogostejše primarno izločene faze so a-Al8Fe2Si, ß-Al5FeSi in 5-Al9FeSi2. V zlitini AlSi12Cu(Fe) je bila primarno izločena faza ß-AlFeSi, na katero se je nalagalo tudi železo od raztapljanja Fe-žičke. Najvišjo koncentracijo železa aluminiju smo dobili z raztapljanjem žičke pri 750 °C in času 30 min. Krivulja koncentracijskega diagrama se izravna nekje na oddaljenosti 4 mm od žičke, vsebnost Fe v aluminiju pa pade na 0,5 mas.% Fe. Pri aluminije -vi zlitini pa vsebnost železa v aluminijevi zlitini pade že na 1 mm od žičke na 0,3 mas. %, pri raztapljanju žičke na 750 °C 30 min. Z večanjem deleža železa v zlitini se znižuje temperatura tališča, temperatura tališča evtektika pa se zvišuje. Z večanjem deleža železa v zlitini se zniža tudi toplota, ki se porablja pri taljenju. Prav tako lahko rečemo, da železove faze oddajo manj toplote pri strjevanju, kar je razvidno tudi iz preiskav s simultano termično analizo. F RMZ-M&G 2007, 54 The kinetics of precipitation in Al-Mg and Al-Mg-Cu alloy Kinetika izločanja v zlitinah Al-Mg in Al-Mg-Cu Maja Vončina 1, Primož Mrvar 1, Franc Zupanič2, Jožef Medved 1 'University of Ljubljana, Faculty of Natural Sciences and Engineering, Department of materials and metallurgy, Aškerčeva cesta 12, SI-1000 Ljubljana, Slovenia; E-mail: maja.voncina@ntf.uni-lj.si, primoz.mrvar@ntf.uni-lj.si, jozef.medved@ntf.uni-lj.si 2 University of Maribor, Faculty for Mechanical Engineering, University Center for Electron Microscopy, Smetanova ulica 17, 2000 Maribor, Slovenia; E-mail: franc.zupanic@uni-mb.si Received: November 12, 2007 Accepted: December 18, 2007 Abstract: Aluminium alloys usually contain many alloying elements which form many phases. However, most of the heat-treatable alloys contain combinations of magnesium with one or more of the elements such as copper, silicon and zinc. In this work a triple simple thermal analysis (TETA) was used in order to achieve three different cooling rates and consequently three different stages of supersaturated solid solution. In addition melt spinning was used to obtain highly supersaturated solid solution. The course of equilibrium solidification of the alloys was calculated using the computer simulation (Thermo-Calc). To pursue the sequence of precipitation of hardening precipitates the differential scanning calorimetry (DSC) was used enabling determination of precipitation energy and the temperature of precipitation of precipitates from supersaturated solid solution. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) was used to determine the phases formed during solidification. Using the DSC method the kinetics of precipitation from supersaturated solid solution in our case in AlMg7.5 and AlMg3Cu can be followed very precisely. The precipitation kinetics is related to increasing tendency for energy relaxation on heating DSC curve, and is enhanced with strongly supersaturated solid solutions. If the portion of the precipitation energy is calculated, it can be evident that, in the AlMg7.5 alloy, it increases with the increasing supersaturation. In the AlMg3Cu alloy the precipitation energy also increases from 0.8 % in specimen that was cooled in MC1 to 1.6 % in specimen that was rapidly solidified. Izvleček: Aluminijeve zlitine običajno vsebujejo veliko zlitinskih elementov, zato imajo v mikrostrukturi več faz. Večina toplotno utrjevalnih aluminijevih zlitin vsebuje kombinacijo magnezija z enim ali več elementi, kot so baker, silicij in cink. V tem delu je bila, za dosego različnih stanj prenasičene trdne raztopine, izvedena trojna enostavna termična analiza (TETA), pri čemer so bile dosežene tri različne ohlajevalne hitrosti ter posledično tri različne prenasičene trdne raztopine. Z napravo za hitro strjevanje (Melt Spinner) pa je bila dosežena najbolj prenasičena trdna raztopina. Potek ravnotežnega strjevanja je bil določen z računalniško simulacijo Thermo-Calc. Za zasledovanje zaporedja izločanja utrjevalnih izločkov je bila uporabljena simultana termična analiza (STA) in sicer diferenčna vrstična kalorimetrija (DSC), s katero so bile določene energije izločanja ter temperature izločanja izločkov iz različnih prenasičenih trdnih raztopin. S pomočjo elektronske mikroskopije (SEM) ter energijsko disperzijske spektroskopije (EDS) so bili določeni tipi nastalih izločkov. Ob uporabi DSC metode je omogočeno izredno natančno zasledovanje kinetike izločanja iz prenasičene trdne raztopine, v našem primeru v zlitini AlMg7,5 in AlMg3Cu. Kinetika izločanja je razvidna iz povečevanja sproščene energije izločanja, ki pa s se povečano prenasičenostjo samo še povečuje. Pri izračunu deleža sproščene energije je opaziti, da energija izločanja s prenasičenostjo v zlitini AlMg7,5 naraste. Pri zlitini AlMg3Cu energija izločanja prav tako naraste od 0,8 % v vzorcu predhodno ohlajanem v MC1 na 1,6 % v vzorcu predhodno ohlajenem na Melt Spinnerju. Key words: Al-Mg alloy, Al-Mg-Cu alloy, thermal analysis, differential scanning calorimetry (DSC), precipitation kinetics Ključne besede: zlitina Al-Mg, zlitina Al-Mg-Cu, termična analiza, diferenčna vrstična kalorimetrija (DSC), kinetika izločanja Introduction Al-Mg and Al-Mg-Cu alloys are usually strengthened by nanoparticles that precipitate from a supersaturated solid solution. Nevertheless, most of the heat-treatable alloys contain combinations of magnesium with one or more of the elements like copper, silicon and zinc. Characteristically, even a small amount of magnesium in concert with these elements accelerates and accentuates precipitation hardening. The structural changes, which are formed as a result of precipitation of atoms from solid solution, have extraordinary technological and industrial meaning. changes. Multiple alloying additions of elements employed in commercial alloys are strictly functional and with different heat treatments serve to provide many different combinations of properties[1]. Heat treatment to increase strength of aluminium alloys is a three-step process: 1. Solution heat treatment: dissolution of soluble phases. 2. Quenching: development of supersaturated solid solution. 3. Age hardening: precipitation of solute atoms either at room temperature (natural aging) or elevated temperature (artificial aging)[1]. The majority of heat-treatable aluminium The classical Al-Mg alloy is typically used alloy systems exhibit multistage precipita- for car body construction, where certain tion and undergo accompanying strength problems can occur during the paint-bak- ing treatment, due to the softening of Al-Mg parts. The undesirable softening can be overcome either by using precipitation hardening at paint-baking temperatures (160-180 °C) either with small additions of copper, which makes the alloys precipitation hardenable during paint-baking treatment[1]. During aging of Al-Mg-Cu alloy the precipitation takes place in following sequence: SSS ^ GPB zone ^ S''/GPB2 ^ S' ^ S SSS stands for supersaturated solid solution and GPB for Guinier-Preston-Bagaryatsky[1,2]. The transition phases (GPB zone, S'', S') are formed because they have a lower activation energy barrier for nucleation than the equilibrium phases. S-phase prefers to nucleate on defects, therefore dislocations and dislocation loops are the favoured nucleation sites[1]. In this work we investigated the precipitation kinetics from different supersaturated solid solutions in two alloys: binary AlMg7.5 and ternary AlMg3Cu. The latter alloy was chosen in order to determine the influence of copper on precipitation kinetics. The most important goals were to determine energies and temperatures of precipitation. Experimental The investigated AlMg7.5 and AlMg3Cu alloys were made out of pure electrolytic aluminium (99.98 %), pure magnesium and pure copper. Alloys were melted in graphite crucible and cast into three measuring cells (Table 1) of triple simple thermal analysis (TETA)[1] with a purpose to obtain three different supersaturated solid solutions. These alloys were also casted on the device for rapid solidification (Melt Spinner). The process is schematically presented in Figure 1. During melt spinning the liquid metal is cast upon a fast rotating copper wheel. A stable melt puddle appears when the wheel's velocity attains the critical point (up to 35 m/s). The thickness, width and length of ribbons depend on the wheel's velocity, substrate material, melt superheat, injection pressure, nozzle diameter and the distance between the nozzle and the wheel. Consequently, the ribbons with a thickness range of 10 ^m to a few mm, and with width range of 1 to 12 mm at solidification rate from 102 to 106 K/s are produced[1]. After TETA the specimens were chemically analysed. In order to determine the intensity and the energy of precipitation from various supersaturated solutions the differential scanning calorimetry (DSC) of simultaneous thermal analysis (STA) Jupiter 449c of NETZSCH enterprise was used. With a purpose to determine phase formed during solidification in investigated alloys the Scanning Electron Microscopy (SEM) with EDS analyser (Sirion 400 NC equipped with INCA 350) was used. Table 1. Measuring cells of triple simple thermal analysis Tabela 1. Merilne celice trojne enostavne termične analize Figure Material Cronning sand Gray cast iron Gray cast iron Designation MC1 MC2 MC3 Ejection gas pressure Melt Molten al Ioy puddle Rotating substrate wheel Crucible Heating system Nozzle Free melt jet Figure 1. Scheme of a free jet melt spinner[7] Slika 1. Shematski prikaz naprave Melt Spinner14 Solidified ribbon Table 2. Chemical composition of the investigated alloys Tabela 2. Kemijska sestava preiskovanih zlitin Element/mass.% Alloy Cu Zn Mg Mn Si Ti Fe Al AlMg7.5 0.00061 0.0114 7.572 0.0035 0.0534 0.00012 0.1417 rest AlMg3Cu 0.8451 0.0107 3.253 0.0030 0.0547 0.00002 0.1932 rest Table 3. The course of equilibrium solidification calculated using Thermo-Calc program Tabela 3. Potek ravnotežnega strjevanja, izračunanega s programom Thermo-Calc AlMg7.5 AlMg3Cu Temp. /°C Reaction Temp. /°C Reaction 620 L - «Al 640 L - aAl 606 L - «Al + Al13Fe4 622 L - aM + Al^ 546 L — aAl + Mg2Si 550 aAl — Mg2Si 314 aAl — Al3Mg 396 aAl - AlxMgyCuz 230 aAl - Al15Mg10Cu 293 aAl - Al15Mg10Cu 156 aAl - Al6Mn 253 aAl + AlxMgyC4 - Al15Mg10Cu 50 aAl - Al5Ti 111 aAl - Al6Mn 9 aA, - Al5Ti Results and discussion The chemical composition of the investigated alloys is presented in Table 2. In Table 3 the course of equilibrium solidification of the alloys was calculated using the computer application Thermo-Calc. Equilibrium phase diagrams are shown in Figure 2. From Table 3 and Figure 2 the temperature of primary solidification, eu-tectic solidification and precipitation at equilibrium conditions can be determined. The sequence of solidification can be influenced by concentration of alloying elements (i. e. chemical composition). From the cooling curves in Figure 3 the temperature of primary solidification, solidification of eutectic and the temperature of precipitation in the investigated alloys are evident. With the increasing cooling rate the peaks in differential cooling curve decreases. The alloy is now supersaturated with magnesium in case of AlMg7.5 alloy and magnesium and copper in case of AlMg3Cu alloy. The characteristic temperatures are also changing in dependence of the type and concentration of alloying elements. The solidification of AlMg7.5 and AlMg3Cu alloys is presented in Figure Figure 2. Isopleth equilibrium phase diagram of AlMg7.5 and AlMg3Cu alloy Slika 2. Izopletni ravnotežni fazni diagrami zlitin AlMg7,5 ter AlMg3Cu □ (00 200 300 400 SCO 600 № Figure 3. Cooling curves and differential cooling curves of investigated alloys Slika 3. Ohlajevalne in diferencirane ohlajevalne krivulje preiskovanih zlitin Table 4. The energy and temperature of solidification and melting of specific phases in investigated alloys Tabela 4. Energije in temperature strjevanja in taljenja posameznih faz pri preiskovanih zlitinah AlMg7.5 - MC1 DSC - heating DSC - cooling Temp. /°C Reaction Energy (x0.9513 J/g) Temp. /°C Reaction Energy (x0.9513 J/g) 576.1 L ^ «A -135.47 609.4 L ^ a.l 161.15 529.7 L ^ a., + Al„Fe4 550.5 L ^ a.l + Al„Fe4 447.1 L ^ a a + Mg,Si -1.27 521.5 L ^ a.l + Mg,Si 308.6 aA ^ AlMg 0.07 AlMg7.5 - MC2 606.5 L ^ a.l -262.56 612.4 L ^ a.l 275.40 532.2 L ^ a.l + Al„Fe4 566.7 L ^ a.l + Al.3Fe4 447.2 L ^ a. + Mg,Si -0.23 551.1 L ^ a.l + Mg,Si 279.5 aA ^ AlMg 0.47 AlMg7.5 - MC3 574.0 L ^ a. -287.96 609 L ^ a.l 280.44 532.7 L ^ a. + AJ^e, 545 L ^ a, + Al„Fed 336.1 aA ^ AlMg -6.63 520 L ^ a.l + Mg,Si AlMg7.5 - rapid solidification 556.1 L ^ a. -221.94 618.7 L ^ a.l 220.04 536.1 L ^ a. + AJ^e, 565.4 L ^ a, + Al„Fed 310.0 aAl ^ AlMg -0.89 540.3 L ^ a.l + Mg,Si AlMg3Cu - MC1 DSC - heating DSC - cooling Temp. /°C Reaction Energy (x0.9513 J/g) Temp. /°C Reaction Energy (x0.9513 J/g) 575.5 L ^ a.l -205.10 633.7 L ^ a.l 211.66 508.2 L ^ a.l + Mg,Si -3.521 580.3 L ^ a, + Al„Fed 293.4 a , ^ Al Mg Cu 1.708 489.8 L ^ a.l + M&Si 1.59 AlMg3Cu - MC2 577.5 L ^ a.l -207.38 633.0 L ^ a.l 211.09 511.3 L ^ a.l + Mg,Si -2.04 576.7 L ^ a, + Al„Fed 254.5 a , ^ Al Mg Cu 2.19 477.7 L ^ a.l + M&Si 2.71 AlMg3Cu - MC3 576.3 L ^ a.l -303.75 636.0 L ^ a.l 303.56 510.0 L ^ a.l + Mg,Si -1.88 583.0 L ^ a, + Al„Fed 251.4 aAl ^ AlxMg,Cu 1.38 484.0 L ^ a.l + Mg,Si 2.34 AlMg3Cu - rapid solidification 574.4 L ^ a.l -260.09 635.9 L ^ a.l 256.37 246.5 a.l ^ AlxMgCu 4.28 592.6 L ^ a, + Al„Fed 476.6 L ^ aAl + Mg,Si 0.44 * 0.9513 is a correction factor of STA machine for aluminium alloys at current conditions. RMZ-M&G 2007, 54 3. The primary solidification at the alloy AlMg7.5 occurred at 615 °C or 616.5 °C. The undercooling was 5 °C and the recalescence 1.5 °C. The eutectic (aAl + Al13Fe4) solidified at 546.5 °C, eutectic (aAl + Mg2Si) solidified at 451 °C. These characteristic temperatures are somewhat lower than theoretical ones, because of the unequilibrium solidification of the alloy. AlMg3Cu alloy started to solidify at 640.5 °C or 641 °C (Figure 3). The solidification of eutectic (aAl + Al13Fe4) started at temperature 593 °C. Eutectic (aAl + Mg2Si) solidified at 489.5 °C. As mentioned above, these temperatures result differ from the theoretical ones because of the unequilib-rium solidification. At higher cooling rates the characteristic temperatures of primary and eutectic solidification move to lower temperatures. From DSC curves on Figure 4 and 5 and from Table 4 the energy of formation and melting of specific phases are determined. The temperature where the solidification of specific phase starts (in cooling DSC curve) and temperature where the solidification of specific phase ends (in heating DSC curve) are also determined. Only heating DSC curves of investigated alloys are presented. In AlMg7.5 alloy some changes between the heating DSC curves can be seen. These are the consequences of different cooling rates (Figure 4). It is obvious that the precipitation in specimens is intensified with higher supersaturation of Mg in solid solution; i.e. in specimens cooled with higher cooling rates. During reheating magnesium is precipitated from aAl in a form of AlxMgy precipitates. In Figure 5 the precipitation kinetics can be even clearly seen. Namely, there is a stronger tendency for energy relaxation on heating DSC curves in samples previously cooled with higher rates and a fact that the solid solution in Al-Mg-Cu alloy is more supersaturated solid solutions. At higher magnification it can be clearly seen, that the precipitation temperature decreases with the increasing supersaturation. The energy of precipitation also increases with the increasing supersaturation of the alloy. Here the precipitation of AlxMgyCuz precipitates took place within the primary crystals of aAl. In addition, if the portion of the energy for the precipitation is calculated it can be evident, that the fraction of the precipitation energy is increasing with the increasing supersaturation, so the portion of the precipitates in the microstructure increases. The portion of precipitation energy in AlMg7.5 alloy increases from 0.05 % in specimen that was cooled in MC1 to 0.18 % in specimen that was cooled in MC2 and to 0.3 % at specimen that was rapidly solidified. In the AlMg3Cu alloy the precipitation energy increases from 0.8 % in specimen that was cooled in MC1 to 1.0 % in specimen that was cooled in MC2 and to 1.6 % in specimen that was rapidly solidified. As already mentioned the copper in the alloy accelerates and accentuates precipitation hardening. That is evident from the fraction of precipitation energy in heating DSC curves of AlMg7.5 and AlMg3Cu alloys. The portion of precipitation is higher in AlMg3Cu alloy at each level of the supersaturation. The portion of precipitation energy was calculated as a portion from the total solidification energy (precipitation energy divided with the total Figure 4. Heating DSC curves of specimens made of AlMg7.5 alloy: previously cooled in MC1, previously cooled in MC2 and previously cooled with Melt Spinner Slika 4. Segrevalne DSC krivulje vzorca iz zlitine AlMg7,5: predhodno ohlajene v MC1, predhodno ohlajene v MC2 in predhodno ohlajene na napravi Melt Spinner solidification energy). Furthermore, when the specimen was cooled very quickly the melting of eutectics (aAl + Al13Fe4) and (aAl + Mg2Si), and primary phase takes place in one step. On the other hand, when the cooling of the specimen was slow, the melting of eutectics (aAl + Al13Fe4) and (aAl + Mg2Si), and primary phase takes place in two steps. Using the scanning electron microscope and energy dispersive spectroscopy the microstructure constituents in all investigated alloys were analysed. In Figure 6 the microstructure of AlMg7.5 alloy with the EDS analysis are presented. In the micro-structure primary crystals of aAl and the eu-tectic (aAl + Al13Fe4) are visible. When the specimen was ached in a diluted solution of HF acid for approximately 10 minutes also Al3Mg2 precipitates become visible. In the specimen AlMg3Cu in Figure 7 the primary crystals of aAl and the eutectic (aAl + Al13Fe4) were determined. In the structure the phase on the basis of aluminium with some magnesium and copper were also determined, which did not correspond to stoichiometry that was described in literature[5]. Figure 5. Heating DSC curves of specimens made of AlMg3Cu alloy: previously cooled in MC1, previously cooled in MC2 and previously cooled with Melt Spinner: whole heating curve (a) and heating curve at the precipitation (b) Slika 5. Segrevalne DSC krivulje vzorca iz zlitine AlMg3Cu: predhodno ohlajene v MC1, predhodno ohlajene v MC2 in predhodno ohlajene na napravi Melt Spinner: celotna segrevalna krivulja (a) ter segrevalna krivulja pri izločanju (b) Figure 6. Secondary elektron image of AlMg7.5 alloy (SEM) Slika 6. SEM mikroposnetek zlitine AlMg7,5 (SEM) Composition: 13,68 wt % Mg 42,78 wt% Al 43,53 wt.% Cu -» --Composition: 3,23 wt.% Mg 94,02 wt.% Al 1,99 wt.% Cu 0,77 wt.% Fe Figure 7. Secondary elektron image of AlMg3Cu alloy (SEM) Slika 7. SEM mikroposnetek zlitine AlMg3Cu (SEM) Composition: 56,69 wt.% Al 37,75 wt.% Fe J, 56 wt,%Cu Conclusions From the above presented results a few conclusions can be made: • Using the DSC method the kinetics of precipitation from supersaturated solid solution in our case in AlMg7.5 and AlMg3Cu can be followed very precisely. • The precipitation kinetics is related to increasing tendency for energy relaxation on heating DSC curve, and is enhanced with strongly supersaturated solid solutions. • The temperature of precipitation decreases with the increasing supersaturation. The energy of precipitation also increases with the increasing supersaturation of solid solution. If the portion of the precipitation energy is calculated, it can be evident that, in the AlMg7.5 alloy, it increases with the increasing supersaturation from 0.05 % in specimen that was cooled in MC1 to 0.18 % in specimen that was cooled in MC2 and to 0.3 % at specimen that was rapidly solidified. In the AlMg3Cu alloy the precipitation energy increases from 0.8 % in specimen that was cooled in MC1 to 1.0 % in specimen that was cooled in MC2 and to 1.6 % in specimen that was rapidly solidified. • When comparing the behaviour of both alloys, it becomes evident that copper in the alloy enhances the precipitation. The portion of precipitation was higher in AlMg3Cu alloy in each level of supersaturation. Consequently, more precipitates in the microstructure of the AlMg3Cu alloy can be expected. • Microstructure constituents have been analysed. In specimens, primary crystals of aAl and eutectic (aAl +Al13Fe4) have been observed. In case of AlMg7.5 alloy the Al3Mg2 precipitates were found. In case of AlMg3Cu alloy the precipitates on base of aluminium with some magnesium and copper were determined, which stoichiometry did not correspond to that described in literature[5]. Povzetek Kinetika izločanja v zlitinah Al-Mg in Al-Mg-Cu Aluminijeve zlitine običajno vsebujejo veliko zlitinskih elementov, zato imajo v mikrostrukturi več faz. Večina toplotno utrjevalnih aluminijevih zlitin vsebujejo kombinacijo magnezija z enim ali več elementi, kot so baker, silicij in cink. Že majhna koncentracija magnezija v povezavi s temi elementi pospeši in poudari izlo-čevalno utrjevanje. Strukturne spremembe, ki so posledica izločanja atomov iz trdne raztopine, so izrednega tehnološkega in industrijskega pomena. Večino aluminijevih zlitin utrjujemo večstopenjsko. Dodajanje večjega števila zlitinskih elementov je nujno samo za funkcijske namene ter za določene toplotne obdelave ter tako omogočajo različne kombinacije lastnosti: fizikalne, mehanske, elektromehanske, ki so potrebne za različne aplikacije[1]. Zlitine Al-Mg ter Al-Mg-Cu se utrjujejo z izločanjem nanodelcev iz prenasičene trdne raztopine. V tem delu smo za doseganje različnih stopenj prenasičenja trdne raztopine izvedli trojno enostavno termič- no analizo (TETA), pri čemer so bile dosežene tri različne ohlajevalne hitrosti. S hitrim strjevanjem (Melt Spinner) pa je bila dosežena najbolj prenasičena trdna raztopina. Za zasledovanje zaporedja izločanja utrjevalnih izločkov je bila uporabljena simultana termična analiza (STA) in sicer diferenčna vrstična kalorimetrija (DSC), s katero so bile določene energije izločanja ter temperature izločanja izločkov iz različnih prenasičenih trdnih raztopin. S pomočjo elektronske mikroskopije (SEM) so bili določeni tipi nastalih izločkov. Na osnovi rezultatov preiskav smo prišli do naslednjih zaključkov. S pomočjo DSC metode lahko dokaj podrobno zasledujemo kinetiko izločanja iz prenasičene trdne raztopine, v našem primeru pri zlitinah AlMg7,5 ter AlMg3Cu. Kinetika izločanja je razvidna iz tendence večanja količine sproščene energije na segrevalnih DSC krivuljah pri povečevanju ohlajevalne hitrosti zlitin in vse bolj prenasičeni trdni raztopini. Poleg tega temperatura pričetka izločanja izločkov pada ob povečanju prenasiče-nja trdne raztopine. Če izračunamo delež izločevalne energije opazimo, da se ta pri obeh preiskovanih zlitinah povečuje s pre-nasičenjem trdne raztopine. Pri primerjavi obeh zlitin med seboj lahko zaključimo, da baker v zlitini izločanje izrazito poveča. Z elektronsko mikroskopijo smo v zlitini AlMg7,5 našli izločke Al3Mg2, v zlitini Al-Mg3Cu pa izločke na osnovi aluminija z nekaj magnezija in bakra, katerih stehio-metrija pa ni ustrezala stehiometriji podani v literaturi[5]. References [1] ASM handbook (1991): Volume 4, Heat Treating. ASM International, The Materials Information Company. [2] Romhanji, E., Popovic, M., Glisic, D., Dodok, R., Jovanovic, D. (2006): Effect of annealing temperature on the formability ofAl-Mg4.5-Cu0.5 alloy sheets. Journal of Materials Processing Technology.; Vol. 177, pp. 386-389. [3] Wang, S.C., Starink, M.J. (2007): Two types of S phases precipitates in Al-Cu-Mg alloys. Acta Materi-alia.; Vol. 55, pp. 933-941. [4] Wang, M.J., Starink, N., Gao, N. (2006): Precipitation hardening in Al-Cu-Mg alloys revisited. Scripta Materialia.; Vol. 54, pp. 287-291. [5] Kovarik, L., Miller, M.K., Court, S.A., Mills, M.J. (2006): Origin of the modified orientation relationship for S(S'')-phase in Al-Mg-Cu alloys. Acta Materialia.; Vol. 54, pp. 1731-1740. [6] Medved, J., Mrvar, P. (2006): Thermal Analysis of Mg-Al Alloy. Materials Science Forum.; Vol. 508, pp. 603-608. [7] Lojen, G., Anžel, I., Kneissl, A., Križ - man, A., Unterweger, E., Kosec, B., Bizjak, M. (2005): Microstruc-ture of rapidly solidified Cu-Al-Ni shape memory alloy ribbons. Journal of Materials Processing Technology.; Vol. 162-163, pp. 220-229. Review of materials in medical applications Pregled materialov v medicinskih aplikacijah 1 2 1 2 1 David Bombač , Miha Brojan , Peter Fajfar , Franc Kosel , Rado Turk University of Ljubljana, Faculty of Natural Sciences and Engineering, Aškerčeva cesta 12, SI-1000 Ljubljana, Slovenia; E-mail: david.bombac@ntf.uni-lj.si, peter.fajfar@ntf.uni-lj.si, rado.turk@ntf.uni-lj.si ^University of Ljubljana, Faculty of Mechanical Engineering, Aškerčeva cesta 6, SI-1000 Ljubljana, Slovenia; E-mail: miha.brojan@fs.uni-lj.si, franc.kosel@fs.uni-lj.si Received: November 22, 2007 Accepted: December 14, 2007 Abstract: Medical implants are products that have to satisfy functionality demands defined by the human body as working environment. Ideally, they should have biomechanical properties comparable to those of autogenous tissues without any adverse effects and are regulated in order to ensure safety and effectiveness. The choice of material used for designing a medical implant is governed by biocompatibility, bioadhesion, biofunctionality, corrosion resistance, etc. In these review metallic biomaterials are divided into four subgroups: stainless steels, the cobalt alloys, titanium alloys, and other metals. Some attention is also given to shape memory, polymeric, and ceramic biomaterials for their innovative use in practical medical applications. Izvleček: Medicinski vsadki so izdelki, ki morajo zadovoljiti stroge funkcijske zahteve, ki jih narekuje človeško telo kot delovno okolje. V idealnem primeru naj bi imeli biomehanske lastnosti primerljive avtogenim tkivom brez škodljivih efektov in so evidentirani, da zagotavljajo varnost in uspešnost. Izbira materiala pri načrtovanju medicinskih vsadkov je pogojena z biokompatibilnostjo, bioadhezijo, biofunkcionalnostjo, korozijsko odpornostjo, itd. V tem pregledu so kovinski biomateriali razdeljeni v štiri podskupine: nerjavna jekla, kobaltove zlitine, titanove zlitine in druge kovine. Nekaj pozornosti je posvečene tudi zlitinam s spominom, polimernim in keramičnim biomaterialom zaradi njihove inovativne uporabe v praktičnih medicinskih aplikacijah. Key words: medical implants, biomaterials, AISI 316L, titanium alloys, shape memory alloys, polymeric biomaterials, ceramic biomaterials Ključne besede: medicinski vsadki, biomateriali, AISI 316L, titanove litine, materiali z oblikovnim spominom, polimerni biomateriali, keramični biomateriali Introduction The development of medical implants utilizing new materials continues to attract considerable academic and commercial interest. The development of new biomaterials involves a complicated mix of materials science and cell biology. Collaboration of various experienced specialists such as material scientists, metallurgists, trauma-tologists, orthopedists, chemists, mechanical engineers, pharmacists and others in order to achieve better results in research, development and implementation of the extracted knowledge into the practice is of essential importance. Biomaterials are nonviable materials used in a medical devices intended to interact with biological systems[1] and cover several classes of materials, such as metallic, ceramic, and polymeric materials. Medical implants are products that have to satisfy functionality demands defined by the human body as working environment. Ideally, they should have biomechanical properties comparable to those of autogenous tissues without any adverse effects and are regulated in order to ensure safety and effectiveness. The choice of material used for designing a medical implant is governed by biocompatibility, bioadhesion, biofunc- tionality, corrosion resistance, etc. To better understand implant material-biological organism interaction most of the studies are directed into the releases of particles from the material and offer screens for genotoxicity, carcinogenicity, cytotoxicity, irritation, sensitivity and sterilization agent residues[2]. Focus of this contribution is on metallic, shape memory, polymeric and ceramic biomaterials used in modern medical applications. Metallic biomaterials Metallic biomaterials are often used to support and/or replace components of the skeleton. They are used e.g. as artificial joints, bone plates, screws, intramedullary nails, spinal fixations, spinal spacers, external fixators, pace maker cases, artificial heart valves, wires, stents, and dental implants. They possess greater tensile strength, fatigue strength, and fracture toughness when compared to polymeric and ceramic materials. Most widely used metallic biomaterials for implants devices are 316L stainless steels, cobalt alloys, commercially pure titanium, and Ti-6Al-4V alloys[3-6]. Originally, these materials were developed for industrial purposes. Their excellent mechanical properties and relatively high Table 1. Mechanical characteristics of metal alloys used in medicine* Tabela 1. Mehanske lastnosti kovinskih zlitin uporabljenih v medicini* Characteristics Stainless steel Cobalt alloys Titanium alloys Stiffness High Medium Low Strength Medium Medium High Corrosion Resistance Low Medium High Biocompatibility Low Medium High * the scale is relative corrosion resistance, which results in very small release of harmful toxins when exposed to bodily fluids, are the main reasons for these materials can be left inside the body for a longer period of time and are therefore appropriate for medical uses. In Table 1 some mechanical and biological characteristics of stainless steel, cobalt and titanium alloys are presented. As additional information let us mention that production of metallic-based medical devices in general involves cutting operations (turning, milling, drilling, etc.); forming operations (pressing, hydroform-ing, forging, etc.) and other alternative machining operations (laser and waterjet cutting, different layer-by-layer sintering techniques such as direct metal laser sintering, selective laser melting, selective laser sintering, electron beam melting, and laser engineered net shaping). In these review metallic biomaterials will be divided into four subgroups: stainless steels, the cobalt alloys, titanium alloys, and other metals. Stainless steels Stainless steel used for medical implants is mainly austenitic type 316L due to its resistance to corrosion, together with a wide range of other physical and mechanical properties coupled with inert, easily-to-clean surfaces. The chemical composition of type 316L stainless steel was developed to obtain stable austenitic structure which has numerous advantages, namely: • Austenitic stainless steel has a face-centered cubic structure and is characterized by very low yield strength-to-tensile strength ratio and high form- ability. • To increase strength, cold working and successive strain aging treatment can be applied. • Austenitic stainless steel is superior to ferritic stainless steel in corrosion resistance because the crystallographic atomic density of the former is higher than that of the latter. • Austenitic stainless steel is essentially nonmagnetic. The disadvantages of austenitic stainless steels generally are higher sensitivity toward pitting corrosion and stress corrosion cracking[3]. Pitting corrosion causes deep pits on the metal surface. It is initiated when an oxidant such as dissolved oxygen reacts with chloride ions. Pitting is further accelerated by the existence of an oxygen concentration cell at the early growth stage. The chemical composition of type 316L (ASTM F138, F139) austenitic stainless steel where "L" denotes low carbon content is as follows: <0.030 % C, <1.0 % Si, <2.0 % Mn, <0.045 % P, <0.030 % S, 12.015.0 % Ni, 16.0-18.0 % Cr, and 2.0-3.0 % Mn [1]. Its corrosion resistance is improved by adding molybdenum, increasing nickel and reducing carbon to less than 0.030 %. This steel has less than 0.03 wt.% carbon in order to reduce the possibility of in vivo corrosion. If the carbon content of the steel significantly exceeds 0.03 %, there is increased danger of formation of carbides such as Cr23C6. These tend to precipitate at grain boundaries when the carbon concentration and thermal history have been favorable to the kinetics of carbide growth. In turn, this carbide precipitation depletes the adjacent grain boundary regions of chromium, which has the effect of dimin- ishing formation of the protective chromium-based oxide Cr2O3[7]. The presence of molybdenum as an alloying element in stainless steel reduces both the number and the size of nucleations and metastable pits. This is because bonds in the oxide film are strengthened and active sites caused by the formation of molybdates or of molybdenum oxyhyroxides are eliminated[8]. Due to high content of chromium, 316L stainless steel forms a protective, adherent and coherent oxide film that envelops the entire outer surface. This oxide film, often called passive layer, is intentionally formed when device is manufactured as chromium in the surface layer reacts with oxygen creating Cr2O3. The passive film serve as a barrier to corrosion processes in alloy systems that would otherwise experience very high corrosion rates[9] and has ability of self-healing, when damaged, as chromium in the steel reacts with oxygen and moisture in the environment to reform the protective oxide layer[10]. Cobalt alloys Cobalt alloys may be generally described as nonmagnetic, corrosion and heat resistant where exhibit high strength even at elevated temperature and are also resistant to wear[11]. Many of its properties originate from the crystallographic nature of cobalt, and formation of extremely hard carbides and the corrosion resistance imparted by chromium. Cobalt alloys are difficult to fabricate which is why their use has been limited, but continuous work led to the development of specialized casting methods[12] and recently to selective laser sintering. Due to cobalt alloy excellent resistance to degradation in the oral envi- ronment, the first medical use was in the cast of dental implants. Various in-vitro and in-vivo tests have shown that the alloys are biocompatible and suitable for use as surgical implants. Today the use of Co alloys for surgical applications is mainly related to orthopaedic prostheses for the knee, shoulder and hip as well as to fracture fixation devices. Joint endoprostheses are typical long-term implants, and the applied implant material must therefore meet extremely high requirements with regard to biocompatibility with the surrounding body tissue material and corrosion resistance to bodily fluids[13]. Nowdays the CoCrMo cast and wrought versions of alloy are highly biocompatible materials[14,15] and are widely used as orthopedic implant materials in clinical practice such as hip joint and knee replacement. The biocompatibility of CoCrMo alloy is closely related to its excellent corrosion resistance due to the presence of an extremely thin passive oxide film that spontaneously forms on the alloy surface. Similar to AISI 316L stainless steel predominant oxide film is Cr2O3 with some minor contribution from Co and Mo oxides[16,17]. In spite of the alloys excellent corrosion resistance, there is still some concern about metal ion release from orthopedic implants into the human body environment. Implant components fabricated from Co-Cr based alloys have been reported to produce elevated Co, Cr and Ni concentrations in the surrounding tissue[18,19]. Other Co alloys used in medicine are MP35N or CoNiCrMo (ASTM F 562) with a nickel content of 35 % used for car- diovascular pacing leads, stylets, catheters and orthopaedic cables. Increased content of nickel exhibits an improved resistance to stress-corrosion cracking in aqueous solution, but also increase the possibility of nickel allergy reactions. Therefore these alloys are not ideal for orthopaedic applications. The biocompatibility of the wear particles produced can be troublesome because of the increased surface area of these small particles which are in direct contact with the surrounding medium or tissue material. In work-hardened or work-hardened and aged conditions, this alloy has very high tensile properties which are among the strongest available for implant applications. Other Co-based alloy is L-605 cobalt alloy or CoCrWNi (ASTM F 90) which is used for heart valves and in an annealed condition (ASTM F 1091) for surgical fixation wires. Its mechanical properties are approximately the same as those of Co-CrMo alloys, but after the material is cold worked the mechanical properties more than double. Titanium and its alloys Titanium and its alloy grades started gaining widespread usage as implant materials in the early 1970s. Material specifications and forms of them are detailed in a number of specifications, including ASTM and BS7252/ISO 5832 standards. The majority of Ti-based implants are made of commercially pure titanium (CP-Ti), mainly in Europe, and titanium alloy grade 5 Ti-6Al-4V (ASTM F 1472), mainly in North America. Although CP-Ti offer better corrosion resistance and tissue tolerance than stainless steel, its comparatively lower strength and unfavorable wear properties restricted its usage to certain applications such as pace- maker cases, heart valve cages and reconstruction devices. Selection of titanium alloys for implementation is determined by a level and combination of the most desirable characteristics including immunity to corrosion, biocompatibility, shear strength, density and capability of ossteointegration[20]. The cold worked CP-Ti has been used for dental implant and maxillofacial applications. Interest in the Ti-6A1-4V alloy for total joint prostheses grew significantly in the United States toward the late 1970s because of its high strength, low elastic modulus, excellent corrosion resistance, and good tissue tolerance. Currently, its applications include hip and knee prostheses, trauma fixation devices (nails, plates, screws, and wires), instruments, and dental implants. Due to its relatively poor wear resistance, it was soon realized that the Ti-6A1-4V alloy was not suitable for bearing surface applications as are hip heads and femoral knees, without a coating or surface treatment[21]. Application from titanium alloys for bone trauma fixation applications as spinal fusion devices, pins, bone-plates, screws and intramedul-lary nails are shown in Figure 1. Number of medical devices being made from titanium alloys which are generally preferred comparing to stainless steel and Co-alloys and is increasing, because of their lower modulus of elasticity (it is closer to that of bone), superior biocompatibility and corrosion resistance[22,23]. Recently, new titanium alloy compositions, specifically tailored for biomedical applications, have been developed. These first generation of orthopaedic alloys included Ti-6Al-7Nb[24] and Ti-5Al-2.5Fe [25 26], two alloys with properties similar to Ti-6Al-4V that were developed in response to concerns Figure 1. Examples of implants made of metallic biomaterials Slika 1. Primeri implantatov narejenih iz kovinskih biomaterialov relating V to potential cytotoxicity[27,28] and adverse reaction with body tissues[29]. Further, biocompatibility enhancement and lower modulus has been achieved through the introduction of second generation titanium orthopaedic alloys including Ti-12-Mo-6Zr-2Fe [30,31], Ti-15Mo-5Zr-3Al [32], Ti-15Zr-4Nb-2Ta-0.2Pd and Ti-15Sn-4Nb-2Ta-0.2Pd alloys[33] as well as the almost completely biocompatible Ti-13Nb-13Zr alloy[34,35]. Titanium and its alloys have the inherent property to osseointegrate, enabling use in implants that can remain in place for longer period of time. Since titanium is non-magnetic, patients with titanium implants can be safely examined with magnetic resonance imaging which is convenient for long-term implants. Preparing titanium for implantation in the body involves subjecting it to a high-temperature plasma arc which removes the surface atoms, exposing fresh titanium that is instantly oxidized, whereas may be anodized to produce various colors[36]. Titanium is also used for the surgical instruments used in image-guided surgery. To stimulate ossteointegration, limit resorption and thus increase the implant lifetime, some designs (cementless prostheses) use roughened bioactive coated surfaces. Hydroxyapatite (HA) coatings are used as bioactive surface of titanium implants, of which many surface treatment techniques have been developed[37]. Those techniques are plasma spraying, electrophoretic deposition of HA and micro-arc oxidation. Another form of implant coating is diamondlike carbon (DLC) coatings. DLC coatings can address the main biomechanical problems with the implants currently used, e.g. friction, corrosion and biocompatibility[38]. Metallic surfaces in contact with bodily fluids corrode as their surface dissolves and the dissolved metals enter the blood stream. The frequency of skin sensitivity to metals in patients with artificial joints is substantially higher than that in the general population[39]. At present, the risk to patients to develop such skin reaction after implantation of artificial joints may be considered minimal, cf. Table 2. Table 2. Sensitivity to metal Tabela 2. Občutljivost na kovine Percent Metal Sensitive General population 10 % Patients with stable total joints 25 % Patients with loose total joints 60 % Other metals Conventional metal materials with use of numerous surface coatings and porous designs have been developed to enhance biological fixation of medical implants to bone for use in orthopedic procedures[40]. Other metals used for medical purposes include tantalum, gold, dental amalgams and other special metals. Although excellent clinical results of classical metal materials have been shown, they have several inherent limitations i.e. low volumetric porosity, relatively high modulus of elasticity and low frictional characteristics. To address the limitations of these solid metals, a new porous tantalum biomaterial has been developed. Porous tantalum is an open-cell tantalum structure of repeating dodecahedrons with an appearance similar to cancellous bone comercially known as trabecular metal. Tantalum is a transition metal that remains relatively inert in in-vivo. In the past multiple medical devices have been fabricated that utilize this material, including: pacemaker electrodes, foil and mesh for nerve repair, radiopaque markers, and cranioplasty plates[41,42]. Tantalum-based implants have displayed an exceptional biocompatibility and safety record in orthopedic, craniofacial, and dentistry literature[43]. The basic structure of this po- rous tantalum metal yields a high volumetric porosity, a low modulus of elasticity, and relatively high frictional characteristics. Porous tantalum implants are fabricated from the pyrolysis of a thermosetting polymer foam which in turn creates a low-density vitreous carbon skeleton with 98 % porosity and a repeating dodecahedron array of regular pores. Commercially pure tantalum is then deposited onto this interconnected vitreous carbon scaffold using chemical vapor deposition [40,44,45]. Figure 2 [46], demonstrates the distinct mi-crotexture and overall geometry of this nanostructured porous metal construct and some examples of medical implants. Oxidized zirconium is a metal with a ceramic surface that was introduced commercially for knee arthroplasty components[47,48]. Commercial medical alloy under trade name Oxinium consists of a zirconium and niobium alloy (Zr-2.5Nb) that has been oxidized to transform the surface into zirconia ceramic. The ceramic is not a coating but a transition of metal to ceramic approximately 4-5 ^m thick that is produced by reaction to oxygen during a thermal treatment. The ceramic surface is a monoclinic zirconia ceramic[49,50]. Because the bulk of the material is metal, it does not have the same risk of fracture as a monolithic ceramic head. Thus, the oxidized zirconium implant offers the potential to decrease wear and thereby increase the life span of implants. First oxidized zirconium implants were introduced in 1996 as simple implants. For total knee replacements it has not been used until 2001, and was later used also for hip replacements since 2003. Figure 2. Microstructure of the porous nanostuctured tantalum material and examples of medical devices Slika 2. Mikrostuktura nanostrukturiranega poroznega tantala in primeri medicinskih izdelkov In Figure 3 [51], knee and hip replacemt component from oxidized zirconium are shown. Shape memory materials Shape memory alloys (SMA) have been given a lot of attention mainly for their innovative use in practical applications using shape memory effect (SME). The SME is unique property that some alloys possess according to which, after being deformed at one temperature, they re- cover their original shape by increasing to the alloys second temperature. This effect arises from reversible and usually rate-independent martensitic transformation and resulting changes of crystal structure of the solid phases of the material. The low temperature phase is called martensite phase and the high temperature austenite phase. Large residual strains of even more than 10 % can be recovered in this way and the process is often referred to as free recovery. The return to the original shape starts at a temperature called austenite start transformation temperature AS, and com- pletes at the austenite finish transformation temperature AF. Pseudoelasticity or su-perelastic effect and shape memory effect are two separate mechanical effects which characterize the response of SMA. At constant high temperature, above temperature Af, a mechanical loading-unloading cycle induces highly-nonlinear large deformations. At the end of the loading-unloading cycle no permanent deformations are present. The cycle usually presents a hysteresis loop, Figure 4a. In the early 1960s, researchers at the U.S. Naval Ordnance Laboratory discovered the shape memory effect in an equiatomic alloy of nickel and titanium. Discovered alloy was patented and named Nitinol (Nickel-Titanium Naval Ordnance Laboratory). This discovery is considered a breaktrought in the field of shape memory materials and since that time, intensive investigations have been made to elucidate the mechanics of its basic behavior. The use of NiTi as a biomaterial is fascinating because of its superelasticity and shape memory effect, which are completely new properties compared to the conventional metal alloys. Composition and metallurgical treatments have dramatic impacts on the described transition temperatures. From the applications point of view, NiTi can have three different forms: martensite, stress induced martensite (superelastic), and austenite. In martensite form alloy is soft and ductile and can be easily deformed. Superelastic NiTi is highly elastic, whereas austenitic NiTi is quite strong and hard. The NiTi alloy can exhibit all these properties depending on the temperature in which it is used. In vast majority of medical applications is utilized superelastic effect. Result of slightly nickel richer alloys is superelasticity which could be exhibited in a narrow temperature range of the human body. The Simon Inferior Vena Cava filter was the first SMA cardiovascular device. It is used for blood vessel interruption for preventing pulmonary embolism[52]. The Simon filter is filtering clots that travel inside blood- Figure 3. Microstructure of the porous nanostuctured tantalum material and examples of medical devices Slika 3. Mikrostuktura nanostrukturiranega poroznega tantala in primeri medicinskih izdelkov Figure 4. The stress-strain diagram, SE stents, Nitinol clamps, orthodontic wire Slika 4. Diagram napetost-raztezek, SE stent, Nitinol spona, ortodontska žica stream. The device is made of SMA wire curved similary to an umbrella which traps the clots which are better dissolved in time by the bloodstream. For insertion, the device is exploiting the shape memory effect, i.e. the original form in martensitic state is deformed and mounted into a catheter. When the device is released, body heat causes the filter to return to its original shape. Stents are most rapidly growing cardiovascular products which are used to maintain the inner diameter of a blood vessel. The product has been developed in response to limitations of balloon angioplasty, which resulted in repeated blockages of the vessel in the same area. NiTi alloys have become the material of choice for superelastic self-expanding (SE) stents[53], Figure 4b. The self-expanding nitinol stents are produced in open state and later compressed and inserted into the catheter. The basic open form is obtained mainly by SMA tubing, the final shape is then obtained by alternative machining operations such as laser cutting. Stents can also be produced from wire and laser welded or coiled striped etched sheet. During the operation procedure, when the catheter is in correct position in the vessel, the self-expanding stent is pushed out and then it expands against the vessel wall due to a rise in temperature. Superelastic SMA wires have found wide use as orthodontic wires as well, Figure 4c. Nitinol wires have large elastic deformation combined with a low plateau stress. This results a smaller number of visits to the orthodontist due to the larger elastic stroke and more comfort due to lower stress levels. In dental medicine, special plates for fixing a loose tooth have become available, Figure 4c. They are produced with laser cutting from sheet metal. Orthopedic implants far exceed any other by weight or volume. They are used as fracture fixation devices, which may or may not be removed and as joint replacement devices. As shown in Figure 4a, bone and nitinol have similar stress-strain characteristics, which make nitinol a perfect material for production of bone fixation plates, nails and other trauma implants[54]. In the past, acceptability of nitinol as material for permanent bone implants was conditioned by releasing Ni3+ ions from NiTi and integrity of contact between the bone and the implant. To solve these two vital problems, coating the bioactive layer on the device surface has been introduced[55]. Medical equipment is also a branch where nitinol has found its place. Because modern surgery is aiming less invasive operations, smaller diameters of tubing are very important. Reducing the diameters of medical devices was possible compared to polymer materials due to superelasticity when tubing of NiTi alloys became available. Polymeric biomaterials Polymeric biomaterials are used as a substitute for metal alloys in trauma and orthopedic implant devices or as an aid at surgical procedures. First polymeric material, used in medicine since the 1960s, was ultra-high molecular weight polyethylene (UHMWPE). It is a thermoplastic with extremely long chains and molecular weight numbering between 2 and 6 million. The longer chain serves to transfer load more effectively to the polymer backbone by strengthening intermolecular interactions. Results of this are a very tough material, with the highest impact strength of any thermoplastic presently made. UHMWPE is highly resistant to corrosive chemicals, with exception of oxidizing acids and has extremely low moisture absorption, very low coefficient of friction, characteristic of self lubrication and high resistance to abrasion. The mechanical and tribological properties of UHMWPE favor its use as a bearing material in many joint replace- ment devices. UHMWPE is used in buttons to resurface the patella in total knee arthroplasty, in sleeves to permit semi-constrained rotation in elbow and wrist arthro-plasty designs, and in counterfaces inserted into the glenoid in shoulder arthroplasty. However, for the purposes of this review we will focus on the most common uses of UHMWPE in medical devices, those of tibial bearings in knee arthroplasties and of acetabular bearings in hip arthroplasties[56]. UHMWPE was first used clinically in 1962 and emerged as the dominant bearing material for total hip and knee replacements in the 1970s. Since the 1980s UHMWPE is successfully used for spine implants[57]. Thus, even though UHMWPE components are typically in no imminent danger of wearing through during a patient's lifetime, the generation of particulate debris from the articulating surface has been associated with osteolysis and loosening of implants[58-61]. To address these problems a highly crosslinked UHMWPE materials were clinically introduced in 1998 and has rapidly become the standard of care for total hip replacements[62-68]. Another important medical advancement for UHMWPE in the past decade has been the increase in use of fibers for sutures, where maximum strength and minimum weight are required. It is ideal for orthopedic implants, for example, as it allows smaller implants to be used, and is flexible and resistant to abrasion. Similarly, its strength can be used for surgical instruments for minimally invasive procedures[69]. Polymethyl methacrylate (PMMA) is the synthetic polymer of methyl methacry-late and is in field of medical technologies and implants used because of its good de- gree of compatibility with human tissue. In orthopaedics, PMMA bone cement is used to affix implants and to remodel lost bone. It is supplied as a powder with liquid methyl methacrylate (MMA). When mixed these yield dough like cement that gradually hardens. Surgeons can judge the curing of the PMMA bone cement by pressing their thumb on it. Although PMMA is biologically compatible, MMA is considered to be an irritant and a possible carcinogen and therefore PMMA has also been linked to cardiopulmonary events in the operating room due to hypotension[70-75]. Bone cement acts like a grout and not so much like a glue in arthroplasty. Although sticky, it does not bond to either the bone or the implant, it primarily fills the spaces between the prosthesis and the bone preventing motion. A big disadvantage to this bone cement is that it heats to quite a high temperature while setting and because of this it kills the bone in the surrounding area. It has a Young modulus between the one of cancellous bone and the one of cortical bone, thus it is a load sharing entity in the body not causing bone resorption[76]. Dentures are often made of PMMA, and can be color matched to the patient's teeth and gum tissue. In cosmetic surgery, tiny PMMA microspheres suspended in some biological fluid are injected under the skin to reduce wrinkles or scars permanently. PMMA also is used for replacement intraocular lenses in the eye when the original lens is removed in the treatment of cataracts. Hard contact lenses are frequently made of this material. Soft contact lenses are often made of a related polymer, where acrylate monomers containing one or more hydroxyl groups make them hydrophilic[77-80]. Another polymeric material used as biomaterials for trauma, orthopedic, and spinal implants is polyetheretherketones (PEEK). It is thermoplastic polymer obtained from aromatic dihalides and bisphenolate salts by nucleophilic substitution. The bisphe-nolate salt is formed in situ from bisphenol and either added sodium or added alkali metal carbonate or hydroxide and have extraordinary mechanical properties. PEEK is partially crystalline and has unusual property in exhibiting two glass transition temperatures, at approximately 140 °C and 275 °C, depending on cure cycle and precise formulation. It is also highly resistant to thermal degradation[81]. By the late 1990s, PEEK had emerged as the leading highperformance thermoplastic candidate for replacing metal implant components, especially in orthopedics[82,83] and trauma[84,85]. Numerous studies documenting the successful clinical performance of PEEK polymers in orthopedic and spine patients continue to emerge in the literature[86-91]. Recent research has also investigated the biotribology of PEEK composites as bearing materials and flexible implants used for joint arthroplasty[92-95]. Due to interest in further improving implant fixation, PEEK biomaterials research has also focused on compatibility of the polymer with bioac-tive materials, including hydroxyapatite (HA), either as a composite filler, or as a surface coating[96-100]. As a result of ongoing biomaterials research, PEEK and related composites can be engineered today with a wide range of physical, mechanical, and surface properties, depending upon their implant application. Mechanical properties of PEEK implants can be tailored by preparing carbon-fiber-reinforced (CFR) Table 3. Typical average physical properties of UHMWPE, PMMA and PEEK Tabela 3. Značilne povprečne mehanske lastnosti UHMWPE, PMMA in PEEK ÜHMWPE PMMA peek crf-peek Polymer type Degree of crystallinity [%] Molecular weight [106 g/mol] Poisson ratio Specific gravity Flexural modulus [GPa] Tensile strength [MPa] Tensile elongation [%] Semi-crystalline 39 - 75 2 - 6 0.46 0.932 - 0.945 0.8 - 1.6 39 - 48 350 - 525 Amorphous Noncrystalline 0.1 -0.8 0.35 1.180 - 1.246 1.5 - 4.1 24 - 49 1 - 2 Semi-crystalline 30 - 35 0.08 - 0.12 0.36 1.3 4 93 30 - 40 Semi-crystalline 30 - 35 0.08 - 0.12 0.38 - 0.40 1.4 - 1.6 20 - 135 170 - >2000 1 - 2 composites with varying fiber length and orientation. Comparison of physical properties of UHMWPE, PMMA, PEEK and CFR-PEEK is presented in Table 3 [81]. Property of polymeric materials reviewed earlier (UHMWPE, PMMA and PEEK) is that they are not biadsorbable and biodegradable. Due to high cost of secondary operations, where implants are extracted scientists started research and development of medical devices which are made form bioabsorbable and biodegradable materials. These types of materials have ability to gradually decline in the strength of implant during the healing process where the area of fracture is filled with bone and connective tissue. The rate of dissolving can be engineered in order to be consistent with the rate of new bone growth and under ideal conditions, a bioabsorbable polymer could encourage bone healing while the body slowly metabolizes it[101]. The main advantage of biodegradable implants is elimination of need for a second surgery whereas the main disadvantage is a ten- dency to release harmful acids and other toxins during the dissolving process. The physical properties required for reliable bioabsorbable and biodegradable implants such as appropriate initial strength, initial modulus of elasticity, controlled strength, etc. could be engineered carefully[102]. In general bioabsorbable polymers used in medicine are thermoplastics, linear-chain, partially crystalline or totally amorfous with a definitive melting temperature and/ or a glass transition region. The most used medical polymers are polyglycolide acid (PGA), polylactide acid (PLA) and poly(s-caprolactone) (PCL). Polymers prepared from glycolic acid and lactic acid have found a multitude of uses in the medical industry, beginning with biodegradable sutures first approved in the 1960s [103]. Since that time other medical devices, based on lactic and glycolic acid, as well as other materials, including poly(dioxanone), poly(trimethylene carbonate) copoly-mers, and poly(s-caprolactone) homopolymers and copolymers, have been accepted for use as medical devices[104]. In addition to these approved devices, a great deal of research continues on polyanhydrides[105] polyorthoesters[106] and other materials[107 108]. Fibers from PGA exhibit high strength and modulus and are too stiff to be used as sutures except as braided material. Sutures of PGA lose about 50 % of their strength after two weeks and 100 % at four weeks and are completely absorbed in 4-6 months[101]. PGA is immunological inert, but it leads to slight non-specific lymphocyte activation, as it induces inflammatory mononuclear cell migration[109]. Lactide is the cyclic dimer of lactic acid, which exists as two optical isomers, D and L. L-lactide, is the naturally occurring isomer, and DL-lactide is the synthetic blend of D-lactide and L-lactide. The homopolymer of -lactide (LPLA) is a semicrys-talline polymer. PGA and LPLA exhibit high tensile strength and low elongation and consequently have a high modulus that makes them more applicable than the amorphous polymers for load-bearing applications such as in orthopedic fixation and sutures. Poly(DL-lactide) (DL-PLA) is an amorphous polymer having lower tensile strength and higher elongation and much more rapid degradation time making it more attractive as a drug delivery system. The degradation time of LPLA is much slower than that of DL-PLA requiring greater than 2 years to be completely absorbed[110]. Copolymers of s-caprolactone with DL-lactide have been synthesized to yield materials with more rapid degradation rates[111]. A copolymer of s-caprolactone with glycolide that has reduced stiffness compared to pure PGA is being sold as a monofilament suture. Non-specific inflammatory reactions in living tissue associated with the degradation of the implant sometimes lead to a clinical complication, either to small fluid accumulation under the skin needing no treatment, or to painful fluid accumulation under the skin treated by aspiration with a needle[112]. Polymeric bio-implants are made by traditional melt-molding techniques such as blow molding and injection molding, extrusion, vacuum forming, fiber spinning and sintering technique. They could be produced in the final or semifinal form. The main requirements for polymer bioimplants are sterile production and sterile techniques. To gain better mechanical Figure 5. Bone-fracture fixation polymer screws, rods and plates Slika 5. Polimerni vijaki, žeblji in plošče za fiksacijo fraktur kosti properties the self-reinforcing technique has been introduced[101]. Examples of polymeric material medical devices are sutures, small staple devices, drug delivery devices, small pins, bone-plates and screws, depicted in Figure 5. Ceramic biomaterials In order to avoid the problems associated with random dissolution which include uncontrolled physical degradation, particulate release and long-term durability, the materials need to remain essentially insoluble only to be removed by specific cell activity. Ceramic biomaterials have been developed that not only act as suitable substrates for bone mineralization by osteoblasts but are essentially insoluble in biological media and are resorbed when acted upon by osteoclasts[113]. Zirconium dioxide or zir-conia ceramics (ZrO2) is a bioinert non-resorbable metal oxide which has a good chemical and dimensional stability, and a high strength and toughness[114]. Currently, zirconia ceramic is being recognized for its high strength and surface finish, making this material potentially suitable for the highly loaded environments found in joint replacement. Biomedical grade zirconia was introduced approximately 20 years ago to solve the problem of alumina brit-tleness and the consequent potential failure of implants[115]. Zirconia ceramic has been used to manufacture femoral heads for total hip replacements since the late 1980s [115]. Its color and excellent biocompatibil-ity and mechanical properties have made it attractive for dental applications^16-1201. A prerequisite for successful bone implant integration is direct bone apposition which was observed at bone-zircona interfaces in histological[121-123] and ultrastructural[124] studies suggesting that ZrO2 may also be a suitable implant material. On the one hand, biomedical grade zirconia exhibits the best mechanical properties of oxide ceramics: this is the consequence of phase transformation toughening, which increases its crack propagation resistance. The stress-induced phase transformation involves the transformation of metastable tetragonal grains to the monoclinic phase at the crack tip, which, accompanied by volume expansion, induces compressive stresses[125]. On the other hand, due to this meta-stability, zirconia is prone to ageing in the presence of water[126]. Up to date clinical reports appear to be again somewhat opposite where some results show excellent behavior of some femural heads after several years in vivo[127] while others show poor follow up results[128] with severe wear and osteolysis around the implant. Few case studies report surface degradation of zirconia implants, which could be related to ageing[129,130]. Alumina ceramics (Al2O3) have been used for implants and prostheses for several decades now[131]. The material is characterised by its excellent biocompatibility[132] and high strength, hardness and fracture resistance[133,134]. The resultant high wear resistance is of particular interest for implant components with articulating surfaces like artifical joints. The outstanding wear resistance is the major reason for the predominant use of this material for the femoral joint head [135]. A common material pairing used for hip arthroplasty is a femoral joint head made of alumina and an acetabular liner made of UHMWPE. Inauspiciously alumina is not suitable for implant components with bone contact, because the material is bioinert and thereby no bony ongrowth, and subsequently loosening of the implant occurs[136]. No difference between the biocompatibil-ity of zirconia and that of alumina ceramics has been found in the biological reaction in vivo. Furthermore, the wear factor of UH-MWPE against zirconia ceramic is 40-60 % less than that against alumina ceramic counterfaces and 10-20 % less than that against SUS 316L metal counterfaces[137]. Hydroxyapatite ceramic (HAC) granules are used successfully world-wide as a bone substitute material because of their high biocompatibility. In an orthotopic site, such as a bony defect, bone formation occurs on ceramic surfaces. This newly formed bone bonds tightly to the ceramic surface without any mechanical interlock[138]. Bioactive glasses have been used in many medical applications. However, due to their poor mechanical properties, these glasses cannot be used in load-bearing applications, whereas metallic alloys are still the materials of choice. It was recognized early on that one of the main applications of bioactive glasses could be coatings for prosthetic metallic implants. These coatings serve two purposes: improving the osseointegration of the implants, and protecting the metal against corrosion from the body fluids and the tissue from the corrosion products of the alloys. Unfortunately, most of the attempts to coat metallic implants with bioactive glasses have had limited success due to poor adhesion of the coating and/or degradation of the glass properties during the coating procedure, typically enameling, or flame or plasma spray coating[139]. In recent years, transition metal nitrides like TiN, ZrN, TiAlN, NbN, TaN and VN were successfully used as protective coatings against wear and corrosion in order to increase the life expectancy of surgical implants and prosthesis[140-142]. Conclusions As presented in the article, a variety of different materials and processing technologies are available for medical applications. Which material should be used depends on the type of injury. Medical implants used for temporary healing should be made of conventional metallic biomaterials. The question of the long-term effects of bio-metal, on patients is very important. Further studies relating to long-term effects of materials on biological tissues are necessary, and are likely to lead to an increased understanding of the biocompatibility of materials in the future. Medical implants used for permanent healing are made of titanium alloy due to its inertness and good material characteristics, or polymeric degradable materials due to their properties and possibility of using them together with medicaments and bone healing stimulants. SMA medical devices and implants have been successful because they offered a possibility of performing less invasive surgeries. Nitinol wires in medical instruments are more kink resistant and have smaller diameter compared to 316L or polymer devices. Research to develop a porous SMA which enables the transport of body fluids from outside to inside the bone is currently underway. It was also an intention to provide an overview of uses of polymers in medicine, the field, where is expected an increased number of applications. To addresses the limitations of current surgical techniques a diverse and large number of roles exist for bone biomaterials that are capable of incorporation into the natural process of healing. We expect that in the future, surgeons will have available even more products that will accelerate patient recovery and eliminate secondary surgeries. In the future research and developement of a new perspective that conflates in solidstate physics, biological science as well as materials engineering. The perspective is one that recognizes that future new advances in all these areas will be based on a fundamental understanding of the atomic and molecular infrastructure of materials that has resulted from te past achievemts of physics and chemistry. Major advances will be achieved when the novel behavior, in particular the quantum mechanical behavior, that nanoscale structures possess, can be controlled and harnessed. The next decade should see the emergence of new technologies based on nano-systems with not only improved but hopefully also fundamentally new physico-chemical properties produced at reasonable costs. Experimental and theoretical research should lead to industrial applications yielding important breakthroughs. Povzetek Pregled materialov v medicinskih aplikacijah Medicinski vsadki so izdelki, ki morajo zadovoljiti stroge funkcijske zahteve, ki jih narekuje človeško telo kot delovno okolje. V idealnem primeru naj bi imeli biome-hanske lastnosti primerljive z avtogenim tkivom brez škodljivih efektov in so evidentirani tako, da zagotavljajo varnost in uspešnost. Izbira materiala pri načrtovanju medicinskih vsadkov je pogojena z bio-kompatibilnostjo, bioadhezijo, biofunkci-onalnostjo, korozijsko odpornostjo, itd. V tem pregledu so kovinski biomateriali razdeljeni v štiri podskupine: nerjavna jekla, kobaltove zlitine, titanove zlitine in druge kovine. Nekaj pozornosti je posvečene tudi zlitinam s spominom, polimernim in keramičnim biomaterialom zaradi njihove inovativne uporabe v praktičnih medicinskih aplikacijah. V delu so predstavljeni različni materiali in procesne tehnike, ki so mogoče za medicinske aplikacije. Izbira materiala je pogojena s tipom poškodbe. Medicinski vsadki, ki so začasno v telesu naj bi bili narejeni iz klasičnih kovinskih biomaterialov. Vprašanje kako na pacienta vpliva dolgoročni efekt stika tkivo-kovina je izjemnega pomena. Potrebne so nadaljne študije v zvezi z dolgoročnim vplivom materialov na biološka tkiva, ki bodo po vsej verjetnosti vodile povečanemu razumevanju biokompatibil-nosti materialov v prihodnosti. Medicinski vsadki, namenjeni permanentni uporabi so običajno narejeni iz titanovih zlitin, zaradi njihove inertnosti in dobrih lastnosti, ali iz razgradljivih polimernih materialov zaradi posebnih lastnosti in možnosti hkratne uporabe z zdravili ali stimulanti rasti kosti. Medicinski pripomočki in vsadki narejeni iz materialov s spominom (SMA) so razširjeni in uspešni, ker ponujajo možnost izvršiti manj invazivnih kirurških posegov. Žice in medicinski instrumenti iz nitinola so bolj odporne proti vozljem in omogo- čajo manjše premere v primerjavi z nerjavečim jeklom AISI 316L ali polimernimi pripomočki. Veliko raziskav in razvoja je narejenega tudi na poroznem SMA, ki omogoča prenos telesnih sokov proti kostem. Namen študije je bil tudi zagotovitev pregleda uporabe polimerov v medicini, ki je področje kjer pričakujemo povešanje števila aplikacij. Za odpravo omejitev kururških tehnik obstaja veliko število različnih vlog biomate-rialov, ki so se sposobni vključiti v naravni proces zdravljnja. V prihodnosi pričakujemo, da bodo imeli kirurgi še precej več produktov, ki bodo pospešili pacientovo okrevanje in izključili potrebe po sekundarnih operacijah. References [1] Ratner, B.D., Schoen, F., Hoffman, A., Lemons, J. (2004): Biomaterials Science: An Introduction to Materials in Medicine. Elsevier Science & Technology Books, ISBN: 978-0-125-82463-7. [2] Balazic, M., Brojan, M., Bombac, D., Caram, R. Jr., Kosel, F., Kopac, J. (2007): Titanium and titanium alloy applications in medicine. Surface Engineered Surgical Tools and Medical Devices. Editors: Jackson, J. , Ahmed, W., Springer, ISBN: 978-0-387-27026-5. [3] Sumita, M., Hanawab, T., Teoh, S.H. (2004): Development of nitrogen-containing nickel-free austenitic stainless steels for metallic biomaterials - review. Materials Science and Engineering: C.; Vol. 24, No. 6-8, pp. 753-760. [4] Annual Book of ASTMStandards. Sec- tion 13 - Medical Devices and Services: Medical Devices, 1999. [5] Williams, D.F. (1993): Volume 14: Medical and Dental Materials. Materials Science and Technology: A Comprehensive Treatment. Editors: Cahn, R.W., Haasen, P., Kramer, E.J., Wiley-VCH, ISBN: 978-3-527-26825-2. [6] Breme, J., Biehl, V. (1998): Metallic biomaterials. Handbook of Biomaterials Properties. Editors: Black, J., Hastings, G., Springer, ISBN: 978-0-412-60330-3. [7] Bombac, D., Brojan, M., Krkovic, M., Turk, R., Zalar, A. (2007): Characterization of titanium and stainless steel medical implants [8] [9] [10] [11] [12] [13] [14] [16] [17] [18] surfaces. RMZ - Materials and [15] geoenvironment.; Vol. 54, No. 2, pp.151-164. Ilevbare, G.O., Burstein, G.T. (2001): The role of alloyed molybdenum in the inhibition of pitting corrosion in stainless steels. Corrosion Science.; Vol. 43, No. 3, pp. 485513. Liu, C., Bi, Q., Matthews, A. (2003): Tribological and electrochemical performance of PVD TiN coatings on the femoral head of Ti-6Al-4V artificial hip joints. Surface and Coatings Technology.; Vol. 163164, pp.597-604. Newson, T. (2002): Stainless Steel - A Family of Medical Device Materials. Business briefing: medical device manufacturing & technology. Davids, J.R. (1998): Metals Handbook. ASM International. Shetty, R.H., Ottersberg, WI-I. (1995): Metals in Orthopedic Sur- [19] gery. Encyclopedic Handbook of Biomaterials and Bioengineering. Editors: Wise, D., Trantolo, J.D., Altobelli, E.D., Yaszemski, J.M., Gresser, J.D., Schwartz, E.R., Marcel Dekker, ISBN: 978-0-82479649-5. Sury, P., Semlitsch, M. (1978): Corrosion behavior of cast and forged [20] cobalt-based alloys for double-alloy joint endoprostheses. Journal of Biomedical Materials Research.; Vol. 12, No. 5, pp. 723741. Katti, K.S. (2004): Biomaterials in total joint replacement. Colloids and Surfaces B: Biointerfaces.; Vol. 39, No. 3, pp. 132-142. [21] Long, M., Rack, H.J. (1998): Titanium alloys in total joint replacement -a materials science perspective. Biomaterials.; Vol. 19, No. 18, pp. 1621-1639. Milošev, I., Strehblow, H.-H. (2003): The composition of the surface passive film formed on CoCrMo alloy in simulated physiological solution. Electrochimica Acta.; Vol. 48, No. 19, pp. 2767-2774. Kocijan, a., Milošev, I., Pihlar, B. (2004): Cobalt-based alloys for orthopaedic applications studied by electrochemical and XPS analysis. Journal of Material Science: Materials in Medicine.; Vol. 15, pp. 643-650. Okazaki, Y., Gotoh, E. (2005): Comparison of metal release from various metallic biomaterials in vitro. Biomaterials.; Vol. 26, No. 1, pp. 11-21. Jacobs, J.J., Skipor, A.K., Patterson, L.M., Hallab, N.J., Paprosky, W.G., Black, J., Galante, J.O. (1998): A prospective, controlled, longitudinal study of metal release in patients undergoing primary total hip arthroplasty. Journal of Bone and Joint Surgery.; Vol. 80 A, No. 10, pp. 1444-1458. Rack, H.J., Qazi, J.I. (2006): Titanium alloys for biomedical applications. Materials Science and Engineering: C.; Vol. 26, No. 8, pp. 12691277. Wang, K. (1996): The use of titanium for medical applications in the USA. Materials Science and Engineering: A.; Vol. 213, No. 1-2, pp. 134-137. [22] Dowson, D. (1992): Friction and wear of medical implants and prosthetic devices. ASM Handbook.; Vol. 18, ASM International, Gereland, Materials Park, OH, pp. 656-664. [23] Park, J.B., Lakes, R.S. (1992): Bio- materials - An introduction. 2nd ed, Springer, ISBN: 978-0-30643992-6. [24] Semlitsch, M.F., Weber, H., Streich- er, R.M., Schoön, R. (1992): Joint replacement components made of hot-forged and surface-treated Ti-6Al-7Nb alloy. Biomaterials.; Vol. 13, No. 11, pp. 781-788. [25] Borowy, K-H., Kramer, K-H. (1985): On the properties of a new titanium alloy (TiAl5Fe2.5) as implant material. Titanium '84 Science and Technology.; Vol. 2, Munich, Deutsche Gesellschaft Für Metallkunde EV, pp. 1381-1386. [26] Zwicker, r., Bühler, K., Müller, r., Beck, h., schmid, H-J., Ferstl, J. (1980): Titanium '80 Science and Technology. Warrendale, PA, TMS-AIME, pp. 505-514. [27] Steinemann, S.G. (1980): Corrosion of surgical implants-in vivo and in vitro tests. Evaluation of Biomaterials. Editors: Winter, G.D., Leray, J.L., de Groot, K., John Wiley, ISBN 978-0-471-27658-6. [28] Steinemann, S.G. (1985): Corrosion of titanium and titanium alloys for surgical implants. Titanium '84 Science and Technology.; Vol. 2, Munich, Deutsche Gesellschaft Für Metallkunde EV, 1373-1379. [29] Laing, P.G., Fergosun, A.B. Jr., Hodge, E.S. (1967): Tissue reaction in rabbit muscle exposed to metallic implants. Journal of Biomedical Materials Research.; Vol. 1, No. 1, pp. 135-149. [30] Wang, K., Gustavson, L., Dumbleton, J. (1993): The characterization of Ti-12Mo-6Zr-2Fe. A new biocompatible titanium alloy developed for surgical implants. Beta Titanium in the 1990 S. The Minerals, Metals&Materials Society, pp. 4960. [31] Wang, K., Gustavson, L., Dumble- ton, J. (1993): Low modulus, high strength, biocompatible titanium alloy for medical implants. Titanium '92 Science and Technology. The Minerals, Metals & Materials Society, 2697-2704. [32] Steinemann, SG., Maüsli, P-A., Sz- mukler-Moncler, S., Semlitsch, M., Pohler, o., Hintermann, H-E., Perren, SM. (1993): Beta-titanium alloy for surgical implants. Titanium '92 Science and Technology. The Minerals, Metals & Materials Society, pp. 2689-2696. [33] okazaki, Y., Ito, Y., Ito, a., Tateishi, T. (1993): Effect of alloying elements on mechanical properties of titanium alloys for medical implants. Materials Transactions JIM.; Vol. 34, No. 12, pp. 12171222. [34] Kovacs, P., Davidson, JA. (1993): The electrochemical behavior of a new titanium alloy with superior bio-compatibility. Titanium '92 Science and Technology. The Minerals, Metals& Materials Society, pp. 2705-2712. [35] Mishra, A.K., Davidson, J.A., Kovacs, P., Poggie, R.A. (1993): Ti- 13Nb-13Zr: a new low modulus, high strength, corrosion resistant near-beta alloy for orthopaedic implants. Beta Titanium in the 1990 's. The Minerals, Metals & Materials Society, pp. 61-72. [36] Edwards, J. (1997): Coating and Sur- face Treatment Systems for Metals. Finishing Publications and ASM International, pp. 39-40, ISBN 0-904477-16-9. [37] Chen, J.Z., Shi, Y.L., Wang, L., Yan, F Y., Zhang, F.Q. (2006): Preparation and properties of hydroxya-patite-containing titania coating by micro-arc oxidation. Materials Letters.; Vol. 60, No. 20, pp. 25382543. [38] Dearnaley, G., Arps, J. (2005): Bio- medical applications of diamondlike carbon (DLC) coatings: a review. Surface and Coatings Technology.; pp.2518-2524. [39] Hallab, N., Merritt, K., Jacobs, J.J. (2001): Metal sensitivity in patients with orthopaedic implants. Journal of Bone and Joint Surgery.; Vol. 83 A, No. 3, pp. 428433. [40] Bobyn, J.D., Stackpool, G.J., Hack- ing, S.A., Tanzer, M., Krygier, J.J. (1999): Characteristics of bone ingrowth and interface mechanics of a new porous tantalum biomaterial. Journal of Bone and Joint Surgery.; Vol. 81 B, No. 5, pp. 907-914. [41] Black, J. (1994): Biological perform- ance of tantalum. Clinical Materials.; Vol. 16, No. 3, pp. 167-173. [42] Levine, B.R., Sporer, S., Poggie, R.A., Della Valle, C.J., Jacobs, J.J. (2006): Experimental and clinical performance of porous tantalum in orthopedic surgery. Biomaterials.; Vol. 27, No. 27, pp. 4671-4681. [43] Kato, H., Nakamura, T., Nishiguchi, S., Matsusue, у., Kobayashi, M., Miyazaki, T., Kim, H.-M., Kokubo, T. (2000): Bonding of alkali- and heat-treated tantalum implants to bone. Journal of Biomedical Materials Research.; Vol. 53, No. 1, pp. 28-35. [44] Zardiackas, L.D., Parsell, D.E., Dil- lon, L.D., Mitchell, D.W., Nunnery, L.A., Poggie, R.A. (2001): Structure, metallurgy, and mechanical properties of a porous tantalum foam. Journal of Biomedical Materials Research.; Vol. 58, No. 2, pp. 180-187. [45] Hacking, S.A., Bobyn, J.D., Toh, K., Tanzer, M. and Krygier, J.J. (2000): Fibrous tissue ingrowth and attachment to porous tantalum. Journal of Biomedical Materials Research.; Vol. 52, No. 4, pp. 631-638. [46] http://www.zimmer.com/z/ctl/op/glo- bal/action/1/id/33/template/MP/ navid/312. [47] Ries, M., Salehi, A., Widding, K., Hunter, G. (2002): Polyethylene wear performance of oxidized zirconium and cobalt-chromium knee components under abrasive conditions. Journal of Bone and Joint Surgery.; Vol. 84 A, No. 2, pp. 129-135. [48] Hunter, G., Long, M. (2000): Abra- sive wear of oxidized Zr-2.5Nb, CoCrMo, and Ti-6Al-4V against bone cement. 6th World Biomate- rials Congress Transactions. Society For Biomaterials, Minneapolis. [49] Benezra, V., Mangin, S., Treska, M., Spector, M., Hunter, G., Hobbs, L.W. (1999): Microstructural investigation of the oxide scale on Zr-2.5Nb and its interface with the alloy substrate. Biomedical Materials: Drug Delivery, Implants and Tissue Engineering. Editors: Neenan, T., Marcolongo, M., Valentini, R.F., Materials Research Society Symposium Proceedings, Vol. 550, Materials Research Society, pp. 337-342, ISBN: 978-1558-99456-0. [50] Hunter, G. (2001): Adhesion testing of oxidized zirconium. Transactions of the Society for Biomaterials.; Vol. 24, pp. 540. [51] http://www.oxinium.co.uk/patients/ material.php [52] Yanli, C., Chunyong, L., Shengli, Z., Zhenduo, C., Xianjin, Y. (2006): Formation of bonelike apatite -collagen composite coating on the surface of NiTi shape memory alloy. Scripta Materialia.; Vol. 54, No. 1, pp. 89-92. [53] Duerig, T.W., Tolomeo, D.E., Wholey, M. (2000): An overview of su-perelastic stent design. Minimally Invasive Therapy & Allied Technologies..; Vol. 9, No. 3-4, pp. 235246. [54] Morgan, N.B. (2004): Medical shape memory alloy applications the market and its products. Materials Science and Engineering A.; Vol. 378, No. 1-2, pp. 16-23. [55] Duerig, T.W., Pelton, A., stoeckel, d. (1999): An overview of nitinol medical applications. Materials Science and Engineering A.; Vol. 273-275, pp. 149-160. [56] Kurtz, s.M., Muratoglu, o. K., Evans, M., Edidin, a. a. (1999): Advances in the processing, sterilization, and crosslinking of ultrahigh molecular weight polyethylene for total joint arthroplasty. Biomaterials.; Vol. 20, No. 18, pp. 1659-1688. [57] Kurtz, s.M. (2004): The UHMWPE Handbook: Ultra-High Molecular Weight Polyethylene in Total Joint Replacement. Academic Press, New York, ISBN: 978-0-12429851-4. [58] Lewis, G. (1997): Polyethylene wear in total hip and knee arthroplast-ies. Journal of Biomedical Materials Research, Vol. 38, No. 1, pp. 55-75. [59] schmalzried, T.P., Kwong, L.M., JaS-ty, M., sedlacek, R.C., Haire, T.C., o'Connor, D.o., Bragdon, C.R., Kabo, J.M., Malcolm, A.J., Harris, W.H. (1992): The mechanism of loosening of cemented acetabular components in total hip arthroplasty. Analysis of specimens retrieved at autopsy. Clinical Orthopaedics and related research..; Issue 274, pp. 60-78. [60] Xenos, J.s., Hopkinson, W.J., Calla- ghan, J.J., Heekin, R.D., savory, C.G. (1995): Osteolysis around an uncemented cobalt chrome total hip arthroplasty: Polyethylene wear. Clinical Orthopaedics and related research.; Issue 317, pp. 29-36. [61] Livingston, B.J., Chmell, M.J., Spec- tor, M., Poss, R. (1997): Complications of total hip arthroplasty associated with the use of an acetabular component with a Hylamer liner. Journal of Bone and Joint Surgery.; Vol. 79 A, Issue 10, pp. 1529-1538. [62] Li, S., Burstein, A.H. (1994): Ultra- high molecular weight polyethylene. The material and its use in total joint implants. Journal of Bone and Joint Surgery.; Vol. 76 A, No. 7, pp. 1080-1090. [63] Premnath, V., Harris, W.H., Jasty, M., Merrill, E.W. (1996): Gamma sterilization of UHMWPE articular implants: an analysis of the oxidation problem. Biomaterials.; Vol. 17, No. 18, pp. 1741-1753. [64] Sauer, W.L., Anthony, M.E. (1998): Predicting the clinical wear performance of orthopaedic bearing surfaces. Alternative bearing surfaces in total joint replacement. Editors: Jacobs, J.J., Craig, T.L., American Society for Testing and Materials, West Conshohoken, ISBN: 978-0-803-12490-5. [65] McKellop, H.a. (1998): Wear as- sessment. The adult hip. Editors: Callaghan, J.J., Rosenberg, A.G., Rubash, H.E., Lippincott-Raven Publishers, Philadelphia, ISBN: 978-0-397-51704-6. [66] Eyerer, P., Ellwanger, r., Federolf, H.-A., Kurth, M., Madler, h. (1990): Polyethylene. Concise encyclopaedia of medical and dental materials. Editors: Williams, D., Cahn, R., Pergamon, Oxford, ISBN: 978-0-080-36194-9. [67] Fisher, J., Dowson, d. (1991): Tribo- logy of total artificial joints. Proceedings of the Institution of Mechanical Engineers, Part H.; Vol. 205, No. 2, pp. 73-79. [68] Klein, P.G., Gonzalez-orozco, J.A., Ward, i.M. (1991): Structure and morphology of highly oriented radiation crosslinked polyethylene fibres. Polymer.; Vol. 32, No. 10, pp. 1732-1736. [69] http://www.dsm.com/en_US/html/ hpf/dyneema_purity.htm. [70] Ellis, R.H., Mullvein, J. (1974): The cardiovascular effects of methyl-methacrylate. Journal of Bone and Joint Surgery.; Vol. 56 B, No. 1, pp. 59-61. [71] Gresham, G.A., Kuczynski, A., Ros -borough, D. (1971): Fatal fat embolism following replacement arthroplasty for transcervical fractures of femur. British Medical Journal.; Vol. 2 (5762), pp. 617619. [72] Homsy, C.A., Tullos, H.S., Anderson, M.S., Diferrante, N.M., King, J.W. (1972): Some physiological aspects of prosthesis stabilization with acrylic polymer. Clinical Orthopaedics and related research.; Issue 83, pp. 317-328. [73] Phillips, H., Cole, P.V., Lettin, A.W.F. (1971): Cardiovascular effects of implanted acrylic bone cement. British Medical Journal.; Vol. 3(5772), pp. 460-461. [74] Orsini, E.C., Byrick, R.J., Mullen, J.B.M., Kay, J.C., Waddell, J.P. (1987): Cardiopulmonary function and pulmonary microemboli during arthroplasty using cemented or non-cemented components. Jour- al. Ophthalmology.; Vol. 112, No. nal of Bone and Joint Surgery.; 11, pp. 2004-2008. Vol. 69, No. 6, pp. 822-832. [81] Kurtz, S.M., Devine, J. N. (2007): [75] Kaufmann, T.J., Jensen, M.E., Ford, PEEK biomaterials in trauma, G., Gill, L.L., Marx, W.F., Ka- orthopedic, and spinal implants. llmes, D.F. (2002): Cardiovascu- Biomaterials.; Vol. 28, No. 32, pp. lar Effects of Polymethylmeth- 4845-4869. [82] acrylate Use in Percutaneous Ver- Liao, K. (1994): Performance charac- tebroplasty. American Journal of terization and modeling of a com- Neuroradiology.; Vol. 23, No. 4, posite hip prosthesis. Experimen- pp. 601-604. tal Techniques.; Vol. 18, No. 5, pp. [76] Miller, M.D. 82004): Review of Or- 33-38. [83] thopaedics 4th Edition. W.B. Maharaj, G.R., Jamison, R.D. (1993): Saunders Company, ISBN: 978-0- Intraoperative impact: charac- 721-60364-3, 129. terization and laboratory simula- [77] olson, R.J., Crandall, A.s. (1998): tion on composite hip prostheses. Silicone vs polymethylmethacr- Composite Materials for Implant ylate intraocular lenses with re- Applications in the Human Body: gard to capsular opacification. Characterization and Testing. Ed- Ophthalmic Surgery and Lasers.; itors: Jamison, R.D., Gilbertson, Vol. 29, No. 1, pp. 55-58. L.N., ASTM, Philadelphia, ISBN: [78] osHiKA, T., Nagahara, K., Yaguchi, 978-0-803-11852-2, 98-108. S. (1998): Three-year prospective, [84] Kelsey, D.J., springer, G.s., Good - randomized evaluation of intraoc- man, s.B. (1997): Composite im- ular lens implantation through 3.2 plant for bone replacement. Jour- mm and 5.5 mm incisions. Journal nal of Composite Materials.; Vol. of Cataract & Refractive Surgery.; 31, No. 16, pp. 1593-1632. Vol. 24, No. 4, pp. 509-514. [85] Corvelli, A.A., Biermann, P.J., Rob - [79] Kruger, A.J., schauersberger, J., erts, J.C. (1997): Design, analy- Abela, C., schild, G., Amon, M. sis, and fabrication of a composite (2000): Two-year results: sharp vs segmental bone replacement im- rounded optic edges on silicone plant. Journal of Advanced Mate- lenses. Journal of Cataract & Re- rials.; Vol. 2, No. 1, pp. 2-8. fractive Surgery.; Vol. 26, No. 4, [86] Toth, J.M., Wang, M., Estes, B.T., pp. 566-570. scifert, J.L., seim, III H.B., Turn - [80] Findl, o., Buehl, W., Menapace, er, A.s. (2006): Polyetheretherke- R., sacu, s., Georgopoulos, tone as a biomaterial for spinal ap- M.,Rainer, G. (2005): Long-term plications. Biomaterials.; Vol. 27, Effect of Sharp Optic Edges of a No. 3, pp. 324-334. [87] Polymethyl Methacrylate Intraoc- Brantigan, J.W., Neidre, A., Toohey, ular Lens on Posterior Capsule J.s. (2004): The Lumbar I/F Cage Opacification: A Randomized Tri- for posterior lumbar interbody fu- [88] [89] [90] [91] [92] sion with the variable screw placement system: 10-year results of a Food and Drug Administration clinical trial. The Spine Journal.; Vol. 4, No. 6, pp. 681-688. Brantigan, J.W., Steffee, A.D., Lewis, M.L., Quinn, L.M., Persenaire, J.M. (2000): Lumbar interbody fusion using the Brantigan I/F cage for posterior lumbar interbody fusion and the variable pedicle screw placement system: two-year results from a Food and Drug Administration investigational device exemption clinical trial. Spine.; Vol. 25, No. 11, pp. 1437-1446. Akhavan, S., Matthiesen, M.M., Schulte, L., Penoyar, T., Kraay, M.J., Rimnac, C.M., Goldberg, V.M. (2006): Clinical and histologic results related to a low-modulus composite total hip replacement stem. Journal of Bone and Joint Surgery.; Vol. 88 A, No. 6, pp. 1308-1314. Glassman, A.H., Crowninshield, R.D., Schenck, R., Herberts, P. (2001): A low stiffness composite biologically fixed prosthesis. Clin Orthop Relat Res (393), pp. 128-136. Kärrholm, J., Anderberg, C., Snor -rason, F., Thanner, J., Langeland, N., Malchau, H., Herberts, P. (2002): Evaluation of a femoral stem with reduced stiffness. A randomized study with use of radios-tereometry and bone densitometry. Journal of Bone and Joint Surgery.; Vol. 84 A, No. 9, pp. 16511658. Wang, a., Lin, R., Stark, C., Dumb -leton, J.H. (1999): Suitability and [93] [94] [95] [96] [97] [98] limitations of carbon fiber reinforced PEEK composites as bearing surfaces for total joint replacements. Wear.; Vol. 225-229, Part 2, pp. 724-727. Jones, E., Wang, A., Streicher, R. (2001): Validating the limits for a PEEK composite as an acetabular wear surface. 27 th Annual Meeting of the Society for Biomaterials in conjunction with the 33rdInternational Biomaterials Symposium. Joyce, T.J., Rieker, C., unsworth, A. (2006): Comparative in vitro wear testing of PEEK and UHMWPE capped metacarpophalangeal prostheses. Bio-Medical Materials and Engineering.; Vol. 16, No. 1, pp. 1-10. Manley, M., ong, K., Kurtz, S.M., Rushton, N., Field, R.E. (2007): Biomechanics of a PEEK horseshoe-shaped cup: comparisons with a predicate deformable cup. Transactions of the 53rd Orthopedic Research Society.; Vol. 32, 1717. Yu, S., Hariram, K.P., Kumar, R., Cheang, P., Ak, K.K. (2005): In vitro apatite formation and its growth kinetics on hydroxyapa-tite/polyetheretherketone biocom-posites. Biomaterials.; Vol. 26, No. 15, pp. 2343-2352. Fan, J.P., Tsui, C.P., Tang, C.Y., Chow, C.L. (2004): Influence of interphase layer on the overall elasto-plastic behaviors of HA/PEEK biocomposite. Biomaterials.; Vol. 25, No. 23, pp. 5363-5373. Tan, K.H., Chua, C.K., Leong, K.F., Cheah, C.M., Cheang, P., Abu Bakar, M.S., Сна, S.W. (2003): Scaffold development using selective laser sintering of poly-etheretherketone - hydroxyapatite biocomposite blends. Biomaterials.; Vol. 24, No. 18, pp. 3115- [104] 3123. [99] Abu Bakar, M.S., Cheng, M.H.W., Tang, S.M., Yu, S.C., Liao, K., Tan, C.T., Khor, K.A., Cheang, P. (2003): Tensile properties, tension [105] - tension fatigue and biological response of polyetheretherketone - hydroxyapatite composites for load-bearing orthopedic implants. Biomaterials.; Vol. 24, No. 13, pp. 2245-2250. [100] Ha, S.W., Kirch, M., Birchler, F., [106] Eckert, K.-L., Mayer, J., Winter -mantel, E., Sittig, C., Pfund-Klin -genfuss, I., Textor, M., Spencer, N.D., Guecheva, M., Vonmont, H. (1997): Surface activation of polyetheretherketone (PEEK) and [107] formation of calcium phosphate coatings by precipitation. Journal of Materials Science: Materials in Medicine.; Vol. 8, No. 11, pp. 683690. [101] Middleton, J.C., Tipton, A.J. (2000): Synthetic biodegradable polymers [108] as orthopaedic devices. Biomaterials.; Vol. 21, No. 23, pp. 23352346. [102] Törmälä, P., Pohjonen, T., Rokkanen, P. (1998): Bioabsorbable polymers: materials technology and surgical applications. Journal of [109] Engineering in Medicine.; Vol. 212, No. 2, pp. 101-111. [103] Gilding, D.K., Reed, A.M. (1979): Biodegradable polymers for use in surgery - polyglycolic/poly(lactic acid) homo-and copolymers: 1. Polymer.; Vol. 20, No. 12, pp. 1459-1464. Barrows, Т.н. (1986): Degradable Implant Materials: A Review of Synthetic Absorbable Polymers and Their Applications. Clinical Materials.; Vol. 1, pp. 233-257. Domb, A.J., Amselem, S., Langer, R., Maniar, M. (1994): Polyan-hydrides as carriers of drugs. Biomedical Polymers: Designed-To-Degrade Systems. Editor: Shalaby, S.W., Hanser Gardner Pubns, pp. 69-96, ISBN: 978-1-569-90159-5. Heller, J., Daniels, A.U. (1994): Poly(orthoesters). Polymers: De-signed-To-Degrade Systems. Editor: Shalaby, S.W., Hanser Gardner Pubns, pp. 35-68, ISBN: 9781-569-90159-5. Kohn, J., Abramson, S., Langer, R. (2004): Bioresorbable and Bioerodible Materials. Biomaterials science. Editors: Ratner, B.D., Hoffman, A.S., Schoen, F.J., Lemons, J.E., Academic Press, pp. 115126, ISBN: 978-0-125-82463-7. Shalaby, S.W., Johnson, R.A. (1994): Synthetic absorbable polyesters. Biomedical Polymers: Designed-To-Degrade Systems. Editor: Shalaby, S.W., Hanser Gardner Pubns, pp. 1-34, ISBN: 978-1569-90159-5. Santavirta, S., Konttinen, Y.T., Saito, T., Gronblad, M., Partio, E., Kemppinen, P., Rokkanen, P. (1990): Immune response to poly- glycolic acid implants. Journal of Bone and Joint Surgery.; Vol. 72, No. 4, pp. 597-600. [110] Bergsma, J.E., de Bruijn, W.C., Ro- [116] zema, F.R., Bos, R.R.M., Boering, G. (1995): Late degradation tissue response to poly(L-lactide) bone plates and screws. Biomaterials.; Vol. 16, No.1, pp. 25-31. [111] Schindler, a., Jeffcoat, r., Kimmel, G.L., Pitt, C.G., Wall, M.E., Zw- [117] iEDiNGER, R. (1977): Biodegradable polymers for sustained drug delivery. Contemporary Topics in Polymer Science.; Vol. 2, pp. 251289. [112] Bostman, o., Hirvensalo, E., Mak- [118] inen, J., Rokkanen, P. (1990): Foreign-body reactions to fracture fixation implants of biodegradable synthetic polymers. Journal of Bone and Joint Surgery.; Vol. 72, [119] No. 4, pp. 592-596. [113] Langstaff, S., Sayer, M., Smith, T.J.N., Pugh, S.M. (2001): Resorbable bioceramics based on stabilized calcium phosphates. Part II: evaluation of biological response. Biomaterials.; Vol. 22, No. 2, pp. [120] 135-150. [114] Piconi, C., Maccauro, G. (1999): Zirconia as a ceramic biomaterial. Biomaterials.; Vol. 20, No. 1, pp. 1-25. [115] Christel, P., Meunier, A., Dorlot, J.M., Crolet, J.M., Witvoet, J., Sedel, L., Boutin, P. (1988): Biomechanical compatibility and design of ceramic implants for [121] orthopedic surgery, Bioceramics: material caracteristics versus in vivo behaviour. Annals of the New York Academy of Sciences.; Vol. 523, pp. 234-256. Ahmad, I. (1998): Yttrium-partially stabilized zirconium dioxide posts: an approach to restoring coronally compromised nonvital teeth. International Journal of Periodon-tics & Restorative Dentistry.; Vol. 18, No. 5, pp. 454-465. Meyenberg, K.H., Luthy, H., Schärer, P., (1995): Zirconia Posts: New All-Ceramic Concept for Nonvital Abutment Teeth. Journal of Esthetic Dentistry.; Vol. 7, No. 2, pp. 73-80. Fritzsche, J. (2003): Zirconium oxide restorations with the DCS pre-cident system. International Journal of Computerized Dentistry.; Vol. 6, No. 2, pp. 193-201. Tinschert, J., Natt, G., Mautsch, W., Spiekermann, H., Anusavice, K.J. (2001): Marginal fit of alumina-and zirconia-based fixed partial dentures produced by a CAD/ CAM system. Operative Dentistry.; Vol. 26, No. 4, pp. 367-374. Glauser, R., Sailer, i., Wohlwend, A., Studer, S., Schibli, M., Schärer, P. (2004): Experimental zirconia abutments for implant-supported single-tooth restorations in esthetically demanding regions: 4-year results of a prospective clinical study. The International Journal of Prosthodontics.; Vol. 17, No. 3, pp. 285-290. Akagawa, Y., Hosokawa, R., Sato, Y., Kamayama, K. (1998): Comparison between freestanding and tooth-connected partially stabilized zirconia implants after two years' function in monkeys: a clinical and histologic study. Journal of Prosthetic Dentistry.; Vol. 80, No. 5, pp. 551-558. [122] Akagawa, Y., Ichikawa, Y., Nikai, H., Tsuru, H. (1993): Interface histology of unloaded and early loaded partially stabilized zirconia endos-seous implant in initial bone healing. Journal of Prosthetic Dentistry.; Vol. 69, No. 6, pp. 599-604. [123] scarano, A., Di Carlo, F., Quaran- ta, M., Piattelli, A. (2003): Bone response to zirconia ceramic implants: an experimental study in rabbits. Journal of Oral Implan-tology.; Vol. 29, No. 1, pp. 8-12. [124] Albrektsson, T., Hansson, H.a., Ivarsson, B. (1985): Interface analysis of titanium and zirconium bone implants. Biomaterials.; Vol. 6, No. 2, pp. 97-101. [125] Garvie, R.C., Hannink, R.H.J., Pas - COE, R.T. (1975): Ceramic Steel?. Nature.; Vol. 258, pp. 703-704. [126] Lawson, s. (1995): Environmental degradation of zirconia ceramics. Journal of the European Ceramic Society.; Vol. 15, No. 6, pp. 485502. [127] Caton, J., Bouraly, J.P., Reynaud, P., Merabet, Z. (2004): Phase Transformation in Zirconia Heads after THA Myth or Reality. Proceedings of the Ninth BIOLOX Symposium.; Vol. 26-27, pp. 73-74. [128] Allain, J., Le Mouel, s., Goutalli- er, d., VoisiN, M.C. (1999): Poor eighth year survival of cemented zirconia-polyethylene total hip re- placements. Journal of Bone and Joint Surgery.; Vol. 81 B, No. 5, pp.835-842. [129] Haraguchi, K., sugano, N., Nishii, T., sakai, T., Yoshikawa, H, ühzono, K. (2001): Phase transformation of a zirconia cermaic head after total hip arthroplasty. Journal of Bone and Joint Surgery.; Vol. 83 B, No. 7, pp. 996-1000. [130] Catledge, s.A., Cook, M., Vohra, Y., santos, E.M., McClenny, M.D., Moore, K.D. (2003): Surface crystalline phases and nanoin-dentation hardness of explanted zirconia femoral heads. Journal of Materials Science: Materials in Medicine.; Vol. 14, No. 10, pp. 863-867. [131] Hulbert, s.F., Young, F.A., Math - ews, R.s., Klawitter, J.J., Talbert, C D., stellino, F.H. (1970): Potential of ceramic materials as permanently implantable skeletal prostheses. Journal of Biomedical Materials Research.; Vol. 4, No. 3, pp.433-456. [132] Griss, P., Werner, E. (1980): Alu- mina ceramic, bioglass and silicon nitride. A comparative biocompat-ibility study. Mechanical Properties of Biomaterials. Editors: Hastings, G.W., Williams, D.F., John Wiley, pp. 217-225, ISBN: 978-0471-27761-3. [133] Green, D.J. (1998): An Introduction to the Mechanical Properties of Ceramics. Cambridge University Press, ISBN: 978-0-521-59913-9. [134] Munz, D., Fett, T. (1999): Ceramics: Mechanical Properties, Failure Behaviour, Materials Selection 1st [135] [136] [137] [138] [139] [140] Ed., Springer Verlag, ISBN: 9783-540-65376-9. Willmann, G. (1998): Überlebensrate und Sicherheit von keramischen Kugelköpfen für Hüftendoproth-esen (Survival rate and reliability of ceramic femoral heads for total hip arthroplasty). Materialwissenschaft und Werkstofftechnik.; Vol. 29, No. 10, pp. 595-604. Fischer, H., Niedhart, C., Kaltenborn, N., Prange, A., Marx, R., Niethard, F.U., Telle, R. (2005): Bioactivation of inert alumina ceramics by hydroxylation. Biomaterials.; Vol. 26, No. 31, pp. 61516157. Yen, s.K., Guo, M.J., Zan, HZ. (2001): Characterization of electrolytic ZrO2 coating on Co-Cr-Mo implant alloys of hip prosthesis. Biomaterials.; Vol. 22, No. 2, pp. 125-133. Holtgräve, E.A., Donath, h. (1995): Response of odontoblast-like cells to hydroxyapatite ceramic granules. Biomaterials.; Vol. 16, No. 2, pp.155-159. Lopez-Esteban, s., saiz, E., Fujino, s., oku, T., suganuma, K., Tom-sia, a. P. (2003): Bioactive glass coatings for orthopedic metallic implants. Journal of the European Ceramic Society.; Vol. 23, No. 15, pp. 2921-2930. Braic, M., Balaceanu, M., Braic, V., Vladescu, A., Pavelescu, G., Al-bulescu, M. (2005): Synthesis and characterization of TiN, TiAIN and TiN/TiAIN biocompatible coatings. Surface and Coatings [141] [142] Technology.; Vol. 200, No. 1-4, pp. 1014-1017. Leng, Y.X., Sun, H., Yang, P., Chen, J.Y., Wang, J., Wan, G.J., Huang, N., Tian, X.B., Wang, L.P., Chu, P.K. (2001): Biomedical properties of tantalum nitride films synthesized by reactive magnetron sputtering. Thin Solid Films.; Vol. 398-399, pp. 471-475. Hübler, r., Cozza, A., Marcondes, T.L., souza, R.B., fiori, F.F. (2001): Wear and corrosion protection of 316-L femoral implants by deposition of thin films. Surface and Coatings Technology.; Vol. 142-144, pp. 1078-1083. Regional sediment yield pattern for the west flowing rivers of Kerala state, India Chandramohan T.1, Balchand A.N.2 1National Institute of Hydrology, Belgaum-590001, Karnataka, India; E-mail: cmohant@yahoo.com 2Cochin University of Science and Technology, Department of Physical Oceanography, Kochi-16, Kerala, India; E-mail: balchand@rediffmail.com Received: December 4, 2007 Accepted: December 19, 2007 Abstract: This study aims to understand the spatial and seasonal distribution of suspended sediment load carried by major west flowing rivers of Kerala State, India, which lies in the humid climatic zone. While comparing sediment yield pattern among individual rivers with the aid of daily discharge and sediment load data, it was noticed that the State could be broadly delineated into four distinct sediment yielding zones. This aspect was dealt in detail and the influencing factors were analyzed. The sediment yield characteristics for each of these zones were explained mainly with respect to the two major rainfall seasons of the State, namely Southwest (SW) monsoon and Northeast (NE) monsoon and their spatial and temporal coverage over the state. Key words: suspended sediment, yield, erosion, discharge, monsoon, Kerala Introduction In recent times, due to various developmental activities within the river basins, the rate of soil erosion, its transport, and deposition downstream have considerably altered. Such changes in sediment movement will have its impact on the river system, reservoirs, estuaries and coastal regions. While studying the environmental problems of a region, land, water, and biomass have to be considered together. An integrated approach has to be followed while suggesting solutions to such problems. Kerala, which is the southernmost state of India, faces numerous environmental issues (Basak , 1998) such as uncontrolled developmental activities on the upstream reaches, land use changes, flash floods, droughts, sedimentation, excessive sand mining, deterioration of water quality, etc. Hence it is important to study the water and sediment yields together and its relation to the drainage basin environment. The Kerala State, situated in the humid tropics lies between 8° 18' and 12° 48' N and 74° 52' and 77° 22' E. Based on the topography, the state can be divided into three well-defined natural landforms: the lowlands with altitude less than 7.5 m; midlands with altitude between 7.5 and 75 m; and the highlands with altitudes greater than 75 m. The state is a narrow strip of land with width varying from 30 km in the north and south to about 130 km in the central region. The Western Ghat forms a continuous mountain wall on the eastern border of the state while Arabian Sea is the margin to west. Geologically the major formations of the state are, crystalline rocks of Archaen age; sedimentary rocks of Tertiary age; laterites capping the crystalline and sedimentary rocks; and recent to sub-recent sediments forming the low-lying areas and river valleys. Lateritic and coastal loams cover the major soil types of the State. There are mainly five broad categories of land use distributed unevenly, arable land, forestland, plantation, grassland and wasteland (Nair, 1987). The average annual rainfall for the State is about 3000 mm. It ranges in the lowland, from 900 mm in the south to 3500 mm in the north; in the midland, from 1400 mm to 4000mm; and in the highland, from 2500 mm to 6000 mm (CWRDM, 1995). About 65 % of this rainfall is received during the southwest (SW) monsoon and 25 % during northeast (NE) monsoon. However, for the southern parts, NE monsoon is active compared to the northern Kerala. Forty-four (44) rivers, with lengths more than 15 km, originate from the Western Ghat, out of which 41 flows towards west and the other three rivers towards east. Periyar, Bharathapuzha, Pamba, and Chal- iyar are the major rivers of the state. The net annual discharge from all these rivers is estimated to be 77,900 MCM (CWRDM, 1995). The drainage basin area and the discharge carried by these rivers are small compared to other major rivers in India. Materials and methods Numerous studies were undertaken in the past to analyze the sediment yield from large and medium rivers of the world (Holeman , 1968; Wilson , 1972; Griffiths , 1982; Keown et al., 1986; Lajczak and Jansson, 1993; Yang et al., 2002). In India also, such studies were carried out for most of the major rivers (Abbas and Subrama -ni an , 1984; Goswami , 1985; Biksham and Subramanian , 1988; Ramesh & Subrama -ni an , 1988; Vaithyanathan et al., 1992; Chakrapani and Subramanian , 1993; Rao et al., 1997). These studies have contributed much to the understanding of the sediment yield processes and the regional factors influencing these processes. In the present study, an attempt was made to understand the spatial and temporal variation of sediment transport characteristics of the rivers of Kerala and the factors affecting this variability. The Central Water Commission (CWC), Govt. of India, is maintaining 16 sediment gauges in Kerala for daily river gauge measurements and sediment sampling. In order to utilize this long-term data, these 16 river basins were selected for the present study. Location of these rivers with the sediment gauge sites is shown in Figure 1. The daily Figure 1. Location of rivers and the sediment gauge sites suspended sediment concentration (mg/l) and corresponding discharge (cumec) data were collected for fifteen years, from 198687 to 2000-01. Average monthly rainfall (mm) for each river basin was calculated from the daily data of rain gauge stations located within these basins. Length of the main streams, average slope and drainage area were extracted from Survey of India toposheets. General and hydrological characteristic of the river basins are given in Table 1. The daily data on suspended sediment concentration [C in mg/l] were converted into sediment load [S in ton]. Daily discharge values were added to get the monthly and yearly discharge in cumec-days. The monthly discharge and sediment load values were used to estimate the percentage monthly and seasonal contributions. While analyzing the sediment and discharge data for the rivers of Kerala, it is noticed that there is a marked change in the pattern (seasonal as well as annual) of carrying capacities of these rivers from north to south. Hence this aspect was studied in detail. Such studies to delineate quantitatively, broad regions with similar erosional patterns were carried out earlier by Griffiths (1982) for North Island basins, New Zealand and Lajczak and Jans -son (1993) for Baltic Drainage basins. charge [S/Q], which is a measure of average sediment concentration, were considered for analyzing the spatial yield characteristics of the rivers. Results and discussion The analysis of seasonal and annual contribution of discharge and suspended sediment load will not yield much inference on the comparative characteristics of individual rivers originating and flowing through different topographical conditions. Sediment load from a river basin depends mainly on the size of the catchment and on the discharge, which carries the sediment. Hence, the erosion rate or sediment yield, which is the ratio of sediment load to catchment area [S/A]; and the ratio of sediment load to dis- Seasonal discharge and sediment contribution for individual rivers is given in Table 2. It can be seen that most of the rivers drain 95-98 % of its sediment load during the monsoon season. However, its distribution during the southwest (SW) and northeast (NE) monsoons gives an entirely different pattern for the rivers flowing through the northern and southern regions of the State. This aspect was analyzed in detail using different criterion. Table 1. Characteristics of the river basins studied Name of the River Annual rainfall (mm) River Basin area [A] (km2) Length (km) Slope (m/m) Annual discharge (MCM) Average annual sediment load (ton) Max. observed sediment conc. (mg/l) Payaswini 4000 957 105 0.012 2384 239934 1090 Valapatanam 3600 1070 101 0.013 3543 252144 613 Chaliyar 3800 1876 169 0.012 4175 401614 1024 Kadalundi 3400 750 86 0.013 1303 85171 345 Bharathpuzha 2300 5755 209 0.009 4326 369186 1163 Pulanthode 2600 940 78 0.013 1756 101771 791 Chalakudy 3600 1342 120 0.010 1798 50234 167 Periyar 3200 4234 244 0.007 6895 320029 739 Muvattupuzha 3100 1208 92 0.011 5068 157001 595 Kaliyar 3000 405 71 0.014 1194 44667 557 Meenachil 3000 615 61 0.017 1756 36566 1091 Manimala 3300 731 90 0.012 1795 70486 559 Pamba 3600 1654 176 0.009 4016 156851 896 Achankovil 2600 810 138 0.005 1247 77130 904 Kallada 2800 1210 92 0.016 1636 104447 802 Vamanapuram 2200 540 88 0.020 701 68619 2944 Table 2. Seasonal variation of % Q and % S for the rivers Name of the River % Discharge [Q] % Sediment Load [S] Monsoon Non- Monsoon Non- SW NE Total monsoon SW NE Total monsoon Payaswini 83.5 13.5 97.0 3.0 90.0 9.5 99.5 0.5 Valapatanam 86.2 11.3 97.5 2.5 94.0 5.3 99.3 0.7 Chaliyar 79.6 15.8 95.4 4.6 87.0 11.9 98.9 1.1 Kadalundi 77.3 20.0 97.3 2.7 79.0 19.6 98.6 1.4 Bharthapuza 74.5 19.7 94.2 5.8 79.9 18.1 98.0 2.0 Pulamthode 72.6 21.8 94.4 5.6 73.8 24.3 98.1 1.9 Chalakudy 75.7 16.8 92.5 7.5 84.2 14.1 98.3 1.7 Periyar 67.9 18.2 86.1 13.9 89.8 8.3 98.1 1.9 Muvattupuzha 56.9 19.2 76.1 23.9 65.9 25.4 91.3 8.7 Kaliyar 77.1 18.9 96.0 4.0 75.7 22.6 98.3 1.7 Meenachil 69.7 22.8 92.5 7.5 71.8 23.7 95.5 4.5 Manimala 69.4 23.6 93.0 7.0 68.1 27.4 95.5 4.5 Pamba 65.5 23.3 88.8 11.2 54.9 40.3 95.2 4.8 Achankovil 62.3 29.7 92.0 8.0 53.9 41.7 95.6 4.4 Kallada 50.7 32.4 83.1 16.9 39.8 53.8 93.6 6.4 Vamnapuram 50.3 35.2 85.5 14.5 41.4 51.4 92.8 7.2 * Seasons as per the Indian Meteorologica Department (IMD) norms M - Monsoon (June to Nov.) NM - Non-Monsoon (Dec. to May) SW - Southwest Monsoon (June to Sept.) NE - Northeast Monsoon (Oct. and Nov.) W - Winter (Dec. to Feb.) S - Summer (March to May) Seasonal and spatial variation of sediment load and discharge Based on the 15 years of data, River Periyar carries maximum yearly discharge (9968 MCM) while Vamanapuram yields the minimum discharge of 288 MCM. Chaliyar supplies the maximum sediment load (0.8 x 106 ton) and Meenachil supplies the minimum (0.02 x 106 ton). The seasonal variation of discharge and sediment load can be represented graphically (Figure 2). A definite grouping of data into four zones: north zone (NZ), north-central zone (NCZ), south-central zone (SCZ) and south zone (SZ), can be observed from the graph for SW and NE monsoon seasons. The rivers from the 4 zones are also shown in separate groups in Table 2. Southwest (SW) monsoon is the major source of discharge for northern rivers. The percentage discharge during SW monsoon decreases steadily from north to south as shown in Table 2, about 84 % in the north to 50 % in the south. On the other hand, the northeast (NE) monsoon yields about 14 % discharge for the rivers from NZ, whereas the percentage increases to 32 % for the SZ rivers. The Muvattupuzha river shows 23 % yield during non-monsoon season, since it includes the diverted water from the tail-race of Idukki hydroelectric project in River Periyar. Major amount of the annual sediment load is transported during monsoon season. SW monsoon sediment load ranges from 74-94 % for northern rivers (NZ + NCZ) whereas Figure 2. Seasonal % (Q Vs S) relationship showing the demarcation of zones this is about 42-76 % for southern rivers (SZ + SCZ). During NE monsoon season, northern rivers (NZ + NCZ) yield 5-24 % of the total sediment load whereas it is 2354 % for the southern rivers (SZ + SCZ). Sediment load for non-monsoon season is nominal for northern rivers while southern rivers register about 2-9 % of the annual sediment load. The sediment yielding characteristics of these individual zones can be further illustrated as in Figure 3, where monthly variation of rainfall [P], discharge [Q] and sediment load [S] contributions of representative rivers from each of the above four zones is demonstrated. It can be seen that the discharge and sediment flow pattern closely follow the monthly rainfall distribution. Northern rivers (NZ + NCZ) showed an asymmetrical uni-mode distribution whereas south-central and SZ Rivers developed a bi-mode distribution. The dominance of NE monsoon rainfall on sediment transport over the southern zone (SZ + SCZ) can be clearly seen. The spatial and seasonal variation of sediment yield [S/A] and average sediment concentration [S/Q] for the rivers are given in Table 3. The division of the State into different zones, as discussed in Figure 2 and Table 2, can be seen in this case also. Average Sediment Concentration [S/Q] This ratio is large for the northern rivers, shows a declining trend towards central rivers and again increases towards south. This denotes high erodibility of the northern and southern zones and indicates the availability of material for transport rather than the stream conditions. Slope of the terrain also is a factor, which is more for the northern and southern Kerala where the land becomes narrow. The specific sediment yielding zones, as explained based on the % [Q-S] relationship is valid here also. When season-wise yield is considered, the trend is similar for monsoon season. The ratio during SW monsoon is more for northern rivers while it is higher during NE monsoon for southern rivers. During the non-monsoon season, the ratio is almost constant except for the southern most rivers, where the summer rains are of appreciable quantity. Sediment Yield [(S/A] From Table 3, it can be seen that the sediment yield is maximum for the northern rivers. The rivers in the central and southern zones show highly unstable values, with a reducing trend towards central parts of the State and increasing towards southern zone. This factor also denotes the high erosion rates for the northern rivers, lesser for southern rivers and least for the central rivers. The presence of four sediment-yielding zones is noticeable in this case also. However, the demarcation between south-central and north-central zones is not so well defined. The unstable values for the central zones (NCZ + SCZ) may be due to the fact that comparatively larger rivers drain this zones. Inter basin water transfer exists between Periyar and Muvattupuzha, which results in large yields even during non-monsoon season. Also, some extreme discharge and sediment load events were noticed for these rivers from the data set, which affects the [S/A] ratio. The effect of these outliers may not appear in [S/Q] ratio, since both discharge and sediment load varies simultaneously. Figure 3. Monthly distribution of (%) rainfall, discharge and sediment load for rivers from different zones Table 3. Variation of the [S/Q] and [S/A] ratios for the rivers Name of the Sediment Load/ Discharge (S/Q) (S/A) River Year M NM SW NE Year M NM SW NE Payaswini 8.7 8.9 1.3 9.4 6.2 250.7 249.6 1.2 225.7 23.9 Valapatanam 6.2 6.3 1.9 6.7 2.9 235.7 233.8 1.8 221.4 12.4 Chaliyar 8.3 8.6 2.1 9.1 6.3 214.1 211.6 2.5 186.2 25.4 Kadalundi 5.7 5.7 3.0 5.8 5.5 113.6 112.0 1.6 89.7 22.3 Bharatapuzha 7.4 7.7 2.5 7.9 6.8 64.2 62.9 1.3 51.3 11.6 Pulanthode 5.0 5.2 1.7 5.1 5.6 108.3 106.2 2.1 79.9 26.3 Chalakudy 2.4 2.6 0.6 2.7 2.0 37.4 36.8 0.7 31.5 5.3 Periyar 4.0 4.6 0.6 5.3 1.8 75.6 74.1 1.5 67.9 6.2 Muvattupuzha 2.7 3.2 1.0 3.1 3.6 130.0 118.6 11.4 85.7 33.0 Kaliyar 3.2 3.3 1.4 3.2 3.9 110.3 108.4 1.9 83.5 25.0 Meenachil 1.8 1.9 1.1 1.9 1.9 59.5 56.8 2.7 42.7 14.1 Manimala 3.4 3.5 2.2 3.3 4.0 96.4 92.1 4.3 65.7 26.5 Pamba 3.4 3.6 1.5 2.8 5.8 91.6 87.1 4.5 50.3 36.9 Achankovil 5.4 5.6 3.0 4.6 7.5 95.2 91.0 4.2 51.3 39.7 Kallada 5.5 6.2 2.1 4.3 9.2 86.3 80.8 5.6 34.4 46.4 Vamnapuram 8.5 9.2 4.2 7.0 12.4 127.1 117.9 9.2 52.6 65.3 Regional Division Based on the analyses of annual and seasonal water and sediment yield, the Kerala State can be roughly divided into four zones with similar sediment transport characteristics. These four zones namely; North Zone (NZ), North-Central Zone (NCZ), South-Central Zone (SCZ), and South Zone (SZ); can be delineated as shown in Figure 4. The difference in transport characteristics among the zones is mainly attributed to the spatial variation of rainfall and discharge, slope along the course of rivers, and physiography of the river basins. The seasonal distribution of discharge and sediment load and the variation in sediment yield, for these four zones, are given in Table 4. The average sediment yield for the northern rivers goes up to 240 ton/km2, whereas for the rest of the state this ranges between 80 and 100. However, the difference in distribution of sediment load and to some extent the discharge, from north to south, during the two monsoon seasons is obvious as can be noticed from the Table 4. Conclusions Water and sediment yield data of 15 years (from 1986-87 to 2000-01) for 16 west flowing rivers of Kerala, India, were collected and analyzed to compare the discharge and suspended sediment carrying characteristics of these rivers. In general, the sediment yield pattern follows the seasonal distribution of rainfall and the topography of the river basin. From the spatial and seasonal analyses of the data, it is found that a broad division of the state into four zones is possible. These are, high sediment yielding North Zone; North-Central Zone with low yield; South-Central Zone with low to medium yield, a sizeable share of which occurs during northeast monsoon season; and South Zone with medium yield, where the yield is almost equal for both the monsoon seasons. The reasons for the above sediment yielding zones for the State is basically due to the spatial distribution of rainfall during the two monsoons over various parts of the State. NE monsoon plays a major roll in the sediment yield characteristics of SZ rivers, whereas SW monsoon is responsible for supplying major share of sediment load for northern rivers (NZ + NCZ). The other factors affecting the variation in suspended sediment transport are slope of the river basin, geology, soil type and land use activities. Acknowledgements The authors acknowledge the Central Water Commission (CWC), for providing sediment data and the facilities offered at Cochin University of Science and Technology (CUSAT), Kerala, for the study. The first author is thankful to National Institute of Hydrology for sanctioning study leave to undertake the doctoral program. Figure 4. Sediment yielding zones of Kerala Table 4. Seasonal distribution of discharge, sediment load and sediment yield for the four zones of the state % Discharge % Sediment Load Sediment Yield (ton/km2) NZ NCZ SCZ SZ NZ NCZ SCZ SZ NZ NCZ SCZ SZ ANNUAL 233.5 79.8 89.4 102.9 MONSOON 96.6 92.9 92.6 86.9 99.2 98.2 96.1 94.0 231.7 78.4 86.1 96.6 SW MONSOON 83.1 73.6 70.4 54.4 90.3 81.3 67.6 45.0 211.1 64.1 60.6 46.1 NE MONSOON 13.5 19.3 22.2 32.4 8.9 16.9 28.5 49.0 20.6 23.3 25.6 50.5 NON-MONSOON 3.4 7.1 7.4 13.3 0.8 1.8 3.9 6.0 1.8 1.4 3.4 6.3 References Abbas , N. & subranaian, V. (1984): Erosion and Sediment Transport in the Ganges River Basin (India). Journal of Hydrology.; Vol. 69, pp. 173-182. Basak, P. (1998): Water Resources of Kerala - Myths and Realities. Water Scenario of Kerala, STEC Technical Report. Government of Kerala. Biksham, G. & Sub ram ani an , V. (1988): Sediment Transport of the Goda-vari River Basin and its Controlling Factors. J. Hydrolo.; Vol. 101, pp. 275-290. Chakrapani, G.J. & Subramanian, V. (1993): Rates of Erosion and Sedimentation in the Mahanadi River Basin, India. J. Hydrolo.; Vol. 149, pp. 39-48. CWRDM (1995): Water atlas of Kerala. Centre for Water Resources Development and Management (CWRDM) Publication, Ko-zhikode, Kerala. Goswami, D.C. (1985): Brahmaputra River, Assam, India: Physiography, Basin Denudation, and Channel Aggradation. Wat. Resour. Res.; Vol. 21, No. 7, pp. 959-978. Griffiths, G.A. (1982): Spatial and Temporal Variability in Suspended Yields of North Island Basins, New Zealand. Wat. Resour. Bull.; Vol.18, No. 4, pp. 575-584. Holeman, J.N. (1968): Sediment Yield of World Rivers. Wat. Resour. Res.; Vol. 4, pp. 737-742. Keown, M.P., Dardeau, E.A. & Causey, E.M. (1986): Historic Trends in the Sediment Flow Regime of the Mississippi River. Wat. Resour. Res.; Vol.22, No. 11, pp. 15551564. Lajczak, A. & Jansson, M.B. (1993): Suspended Sediment Yield in the Baltic Drainage Basin. Nordic Hydrolo.; Vol. 24, pp. 31-52. Nair, K. S. (1987): Hydrometeorological Studies of Kerala State in Relation to the Western Ghats: Ph.D. Thesis. Cochin University of Science & Technology 1987, Kerala, pp. 34-45. Ramesh, R. & Subramanian, V. (1988): Temporal, Spatial and Size Variation in the Sediment Transport in the Krishna Basin, India. J. Hy-drolo.; Vol. 98, pp. 53-65. Rao, S.V.N., Rao, M.V. & Ramasastri, K.S. (1997): A study of Sedimentation in Chenab Basin in Western Himalayas. Nordic Hydrolo.; Vol. 28, No. 3, pp. 201-216. Vaithiyanathan, P., Ram anathan, A. & Subramanian, V. (1992): Sediment Transport in the Cauvery River Basin: Sediment Characteristics and Controlling Factors. J. Hydrolo.; Vol. 139, pp. 197-210. Wilson, L. (1972): Seasonal Sediment Pattern of U.S. Rivers. Wat. Resour. Res.; Vol. 8, No. 6, pp. 14701478. Yang, S., Zhao, Q. & Belkin, I.M. (2002): Temporal Variation in the Sediment Load of the Yangtze River and the Influence of Human Activities. J. Hydrolo.; Vol. 263, pp. 56-71. Technology of producing impressed filters to encompass two layers of aquifers Tehnologija izdelave vtisnega filtra v dva paketa vodonosnikov Željko Vukelič 1, Bojan Lajlar 2, Ivan supovec 3, Goran Vižintin 1 University of Ljubljana, Faculty of Natural Sciences and Engineering, Aškerčeva cesta 12, SI-1000 Ljubljana, Slovenia; E-mail: zeljko.vukelic@ntf.uni-lj.si, goran.vizintin@ntf.uni-lj.si 2Velenje Lignite Mines, Partizanska cesta 78, 3320 Velenje, Slovenia; E-mail: bojan.lajlar@rlv.si 3HGEM d.o.o., Zaloška cesta 143, SI-1000 Ljubljana, Slovenia; E-mail: supovec@hgem.si Received: November 6, 2007 Accepted: December 7, 2007 Abstract: To ensure safe excavation under aquifers it is necessary to employ drainage in order to decrease water pressure in the aquifers above the coal layer. In calculating the permissible height values of excavation, water pressure is one of the most important input data. To obtain real data it is necessary to provide suitable monitoring of the water pressure, which is an indicator of water drainage efficiency. To improve the effects of drainage by using jetted dewatering boreholes, a possible solution was either to install more impressed filters on a shorter distance, or to encompass two aquifers simultaneously through one borehole. We have gradually developed a novel technology of constructing jetted dewatering boreholes also which could encompass two aquifers. This technology can significantly reduce the costs for mine water drainage. Izvleček: Za zagotavljanje varnega odkopavanja pod vodonosnimi plastmi je potrebno v največji možni meri z odvodnjevalnimi procesi znižati tlake vode v vodonosnikih nad premogovim slojem. Tlak vode je tudi eden izmed glavnih vhodnih podatkov pri izračunu dovoljenih višin odkopavan-ja, zato je za pridobitev realnih podatkov potrebno izvajati tudi ustrezen monitoring gibanja tlakov vode, ki so kazalec učinkov odvodnjevanja. Za izboljšanje učinkov odvodnjevanja z vtisnimi filtri, vidimo rešitev predvsem v povečanju gostote izdelave vtisnih filtrov ali v zajemanju dveh vodonosnikov hkrati na eni vrtini. Tako smo razvili popolnoma novo tehnologijo izdelave vtisnih filtrov, ki omogočajo zajem dveh vodonosnikov. Tehnologija zajema dveh vodonosnikov, pomeni tudi občutno znižanje stroškov jamskih odvodnjevalnih objektov. Key words: drilling, two aquifers, jetted dewatering boreholes Ključne besede: vrtanje, dva vodonosnika, vtisni filter 514 VuKELIČ, Ž., LaJLAR, B., SuPOVEC, i., VlžintIn, G. Introduction To ensure safe excavation under aquifers it is necessary to employ drainage in order to decrease water pressure in the aquifers above the coal layer. In calculating the permissible height values of excavation, water pressure is one of the most important input data. To obtain real data it is necessary to provide suitable monitoring of the water pressure, which is an indicator of water drainage efficiency. Due to the excavation in the north-western part of the Preloge coal field, the system of surface piezometers and drift filters has been damaged. Therefore, it was necessary to find a suitable replacement for the system. A good solution to overcome this problem was to install jetted dewatering boreholes, which would replace the drainage system. Since 1990, we have used the technology of vertical and inclined jetted dewatering boreholes by drilling with filter pipes into a single aquifer in the Velenje Coal Mines. In the Skale coal field, intensive drainage from the hanging wall aquifers with in-mine boreholes has been practiced since 1960. To reduce drilling in the cave, the jetted dewatering boreholes, based on drilling technology using screens, is functionally less efficient than the object - a drift filter, which is made from the surface. To improve the effects of drainage by using jetted dewa-tering boreholes, a possible solution was either to install more impressed filters on a shorter distance, or to encompass two aquifers simultaneously through one borehole. Drilling with screens is possible if an inner tube is installed in the screen which will direct the flow of the drilling fluid directly through the drilling crown. During the activation procedure this part is removed. To make the drainage processes more efficient, a suitable solution was to design an jetted dewatering boreholes, which would simultaneously encompasses two aquifers through one borehole, provided that the two aquifers have no hydraulic impact on one another. With this in mind, we have gradually developed a novel technology of constructing jetted dewatering boreholes also which could encompass two aquifers. This technology can significantly reduce the costs for mine water drainage. Geological and hydrogeological conditions Geological characteristics of the Velenje Coal Mines The Velenje depression is of tectonic origin. It was formed already in the Helvet, however, the formation of sediments above the pre-pliocenic layers occurred during the period of late Miocene and at the beginning of Pliocene, during which, due to a series of neotectonic fractures, the whole territory of the Velenje-Dobrnik region sank. This resulted in a depression, which was formed between the Smrekovec and Šoštanj fracture, which is meshed with local fractures of different ages, going in all directions. The valley, as seen today, has been formed by sinking and simultaneous deposition of sediments, and the coal layer has been formed along its synclinal shape. This layer extends over an area which is approx. 8.3 km long and 1.5 to 2.5 km wide. The coal layer is closest to the surface on the edges of the valley, and deepest in the centre, where it reaches a thicknees of 168 m, yielding high quality coal. The layers, which were accumulated by settling of sediments into the depression, represent a complete sedimentation cycle: from the land phase, to marsh land, and lake sedimentation, and back to marsh and land phase. This sequence is frequently broken by fluviatile sediments, sand, and gravel which had been drifted from the north and north-west. Basically, the geological picture of the Velenje synclinal valley consists of Plio-quatenary hanging wall layers, a coal layer, Pliocene layers in the footwall, and a pre-Pliocenic basement. Hanging wall strata The Plioquaternary stratain the hanging wall of the Velenje synclinal valley consist of a series of layers of sand, sand with gravel, silt, arenaceous and clayey silts, arenaceous clays, clays, siltstone and clay-stone, intertwined in vertical and horizontal direction, thus forming a unique multilayer system, which on the vertical line consists of more than a hundred of layers of different thickness. This sedimentary sequence of the hanging wall is mainly in the central, northern and western part of the synclinal valley, while on the southern and eastern part, the hanging wall consists mainly of clays and claystones silts and silstones. Coal layer The coal layer needs to be considered as complex system, consisting of sequences of "Plioquatenary formations" (basement layer, direct footwall, coal layer, Pliocenie hanging wall and Pleistocene hanging wall strata), which are typical for orogenetic active zones. After a short transport period, coarse-grained clastites were deposited from the north-west into the intramontane depression where a lake was formed. On the eastern side, where the possibilities of open-pit mining and underground coal gasification have been considered, the coal layer is relatively poor in terms of quality. However, at the opposite end, on the west, the coal layer dips into depth, becomes thicker, and has better quality. The north-eastern edge is characterised by a steep Triassic slope, where the coal layer becomes thinner and turns upwards. At some places the coal directly contacts the Triassic strata. In the central part on the north, and north-west, numerous layers of clay and sand penetrate into the coal layer. Towards south, these layers become thinner and tail out. In this area too, sand layers can be found in the hanging wall. In Topolšica (on the western side) the coal layer slightly turns up, becomes thinner and tails out. The southern edge of the depression lies directly on the Šoštanj fracture zone, which can be clearly seen from the shape of the coal layer in this area. We can observe sudden changes and interruptions of the layer. In the central part the layer of coal is deepest and of high quality, reaching maximum thickness of 168 metres. The footwall Pliocene strata The pre-Pliocene basement is directly covered by basal layers consisting of green arenaceous silts and sands, while above the triassic layers there is some red and grey clay, followed by direct footwall of a similar formation, with increased content of clay. Pre-Pliocene basement A great part of the pre-Pliocene basement of the Velenje synclinal valley, as well as the most of the eastern, northern and northwestern edge of the valley is composed of Triassic strata of various ages and ly-thology. Triassic strata, particularly those from middle and upper Triassic period, are limestone and dolomites, which make up a system of aquifers. The system is useful for supplying water, however, it also represents a risk for the mine water inrushes due a close proximity of the mine workings and a thin protective layer. The central and southern part of the synclinal valley is composed of Oligocene materials (andezite with tuff and breccia) and Miocene sediments (sandstone and litoth-amnian limestone). Oligocene sediments and Miocene sandstone are impervious and thus not a problem from the hydroge-ological point of view. The Miocene litoth-amnian limestone is an aquifer, however, it covers only a limited area in this mine. In addition, it is not renewed with water, therefore it is irrelevant in this situation. A brief description of hydrogeological problems in the Velenje Coal Mines The geological description of the site shows that the Velenje coal mine consists of two main types of aquifers: the Pliocene gravely-sandy aquifers in the hanging wall, and Triassic (dolomites prevailing) in the footwall. There have been no problems with water during excavations in the southern region of the synclinal valley of the mine since there are no aquifers which could have impact on the excavations, neither in the hanging wall, nor in the footwall. However, the situation is dif- ferent in the central, western, northern and eastern parts: the Preloge coal field lies in the northern part, and the Leženj region is situated on the east. The layer of clay between the coal and the water-bearing sands is very thin, only a few metres thick. Due to high water-pessure in the water-bearing sands lying above the coal, these aquifers represent a potential danger for water and quicksand inrush during excavations, and consequently mean direct risk for safe mining. Since the hanging wall consists of a multi-layer system of aquifers, where individual layers are not necessarily connected, the distribution of pressure in these aquifers varies. This means that hydrody-namic properties of the layers are different too. Because of the potential danger of water and quicksand inrushes, from sandy to silty aquifers close to the hanging wall, it was necessary to decrease water pressure in the lower part of the hanging wall aquifers system to ensure safe mining and to meet the criteria for safe mining (Kočar et al., 1989) to avoid the risk of water inrush. In the period from 1979 to 1988, 36 drift filters were installed in the Velenje coal mine to drain water from the Pliocene hanging wall aquifers. The filters were placed in the following mine dewa-tering roadways named barrage roadway: central barrage roadway (drift filters V-9o to VO-9), north-western barrage roadway (drift filters BV-2 to BV-13), northern barrage roadway (drift filter BV-20), the barrage roadway running along the synclinal valley (drift filters V-11n to V-12z), and southern barrage roadway, or southern barrage upraise roadway (drift filters BV-22 to BV-31). The central barrage roadway was constructed as an experimental roadway already in the period from 1979 to 1981, while other drift filters were constructed later and finished in 1988. Since 1984, the central barrage roadway has been connected with the drainage pipeline system in the PV coal mine. These drift filters are still operating on this roadway, draining the water coming from complex Pliocene hanging wall aquifers. Other drift filters were gradually connected to the drainage system in the mine, and since 1996 they have been serving in this purpose. The design of the drainage system was made based on the experience and knowledge, gained during the experimental drainage in the period 1964-1972. During this period numerous wells for gravitational drainage of water from the hanging wall aquifers into the mine, were made in the Leženj area, together with installation of a series of dewatering boreholes (105 objects), which additionally contributed to decrease the water pressure in the sands above the coal, particularly in the areas where surface drainage system, could not be implemented due to excavation operations. The drainage technology, which was used in the period from 1979 to 1988, was selected upon previous experience and the technology which was used 20 years before that, using submersible pumps to pump water from the wells to the surface (wells NV-1 to NV-4). At that time it was proved that the most efficient method of water drainage is gravitational drainage of water from the hanging wall aquifers via drift filters into the mine. However, hydrogeological conditions above the Šoštanj coal field demanded a different approach to deal with the problem of water drainage. Thus, two wells for pumping water to the surface were constructed during 1998 and 1999 (BV-23 and BV-24), using the so called MOYNO pumps. Considering that before any drainage operation, the levels of water throughout the Plioquternary formations are approximately the same, the drainage of water from the hanging wall aquifers would results in lowering the water level: in the sand layers directly above the coal (and the layers above sand) the level would decrease for more than 350 metres, in the upper layers from 100 m to 150 m, depending on whether the aquifer has been drained directly, or indirectly (by leakage from the superimposed layers). In the Quaternary layers the impact of drainage has not been noticed since these layers were not directly drained. Due to the intermediary sealing layers the connection with the underlying Pliocene layers, is too weak. By simulation of the drainage processes using a mathematical model (1995, 1998) it was proved that, in order to maintain low water-pressure in the sands directly above the coal seam, a good drainage of several subsequent water bearing layers overlying these sands would be needed. Nowadays, in the Preloge coal field, a great part of the drainage system has been abandoned due to coal excavations (the whole central barrage roadway, some wells from the barrage roadway along the synclinal valley, and north-western and northern barrage roadway). Consequently, the quality of the drainage system in the hanging wall layers has deteriorated: the drainage process has become relatively slow and the effects of the elimination of the drainage will only become evident in the near future. In addition to this, there have been some problems with the drainage from both wells used for pumping water to the surface. This calls for the construction of substitutional mine drainage fascilities, which would partially replace the drainage by drift filters. For this purpose we developed a technology of a double screen jetted dewatering boreholes, which is presented further on. Technological implementation of a double screened jetted dewatering boreholes Conventional methods for constructing de-watering boreholes are frequently unreliable due to high pore pressure which occurs in the aquifers. Thus, already in constructing the jetted dewatering boreholes for a single aquifer we developed a technology which is based on cemented technical pipes and drilling with pipe-screen which is built in the aquifer (Veselic et al., 1991; Vukelić, 2005). Drilling with pipe-screen, can be made if an inner pipe is installed into the screen, which will direct the flow of the drilling fluid through the drilling crown. During the activation procedure this part is removed. To rationalise the drainage processes and to improve the effects of drainage it was necessary to consider the construction of a jetted dewatering borehole, which would use one borehole and simul- taneously encompass two aquifers, provided that in terms of hydraulics the two aquifers would not interfere with one another (Vukelić, 2005). The technology was developed and tested in the Velenje coal mine in the borehole No. JV 3175-K/03, located on the transport roadway of the excavating plates G1/B in the north-western part of the Preloge cave. The location is presented in Figure 2. There are two factors which are crucial for a successful implementation of the technology: good understanding of hydrogeological conditions and good geological prognosis. The geological prognostic profile of the borehole JV 3175-K/03 is presented in Figure 1. The main feature of this new technology is that drilling is not interrupted after installing the first screen with a larger diameter into the first layer of sands above the coal: drilling can be continued by loosening the drilling crown and activating the screen in the first aquifer. After the screen has been activated, drilling is continued using the first screen and related pipes as liner to the subsequent aquifer. Drilling is performed with a filter with ф73 mm diameter through the pipe with ф128 mm diameter. After the filter has been installed in the second layer of sand, it is activated. Figure 3 presents the installation of the jetted dewatering borehole into two aquifer layers. Installation procedure of the jetted de-watering borehole into two layers of aquifers Construction of the conductor pipe The conductor pipe is made in a standard way. A borehole for the conductor pipe is drilled with a drilling crown which is Figure 1. Geological prognostic profile of the borehole JV 3175-K/03 Slika 1. Prognozni geološki profil vrtine JV 3175-K/03 Sl VI-m>/AH!)l>NI l'Jtrni-I FAME HRHJ Pa, ч^-ßl qj$lì —q*plì q^Al, — 5o,Q„. (13) siiij = E//II //12 S/ /ln 0ХЦ м*и »км ^//22 их u и хи lIXii Ъппп дои U XU и XU rnixjtu Sub-matrices are of the shape depicted below: (15) The correlatory matrix of measured quantities Lii for u unknowns and n nuxnu measurements is made up of the following sub-matrices: (14) (16) That is how the correlation matrix of measured values is composed of the following sub-matrices: (17) which can, in short, be denoted as: 0-0 их // и x« irxii 0 L/; 22 *" « пи XJÌU 0 0 — Еш> umi мх м пихни (18) The inverse (matrix) of the matrix of measured quantities is thus denoted as: (19) which may, again, be shortened to: For an individual point measurement, we are thus able to obtain the coordinates of the measured point, as well as the submatrix S/ i. 3x3 As has already been depicted in equations (14) to (17), for the determination of a variance-covariance matrix S/ / , it is already nuxnu enough when we are acquainted with the correlation matrices of an individual measurement Si й. The sub-matrices Si и are 3x3 3x3 symmetrical matrices, and can therefore be written as below for each of the individual measurements: (20) and is the row-specific matrix of the inverse correlation sub-matrices S iin of individual uxu measured unknowns č,1, č^, č^, ..., ^ . When we are dealing with the measurements of point positions via the RTK-GPS method, each measurement in itself may beget its own varance-covariance matrix S/i. The variance-covariance matrix Sii nuxnu nuxnu is determined on the basis of different measurement influences of the time. Sad »influences« are, in fact, the disparations of the receiver's an the satellite's timers, the atmosphere's influence upon wave expansion, a mistake pertaining to the determination of the hight of the antennae etc. (21) i , the number of the measurement The evaluations of accuracy of the levelling of an individual quantity The standard deviation of a given levelling procedure - o0 (22) r = nu - u, the number of meaurements above the required number nu, the number of measured quantities i.e .the number of measurements u, the number of sought-for (unknown) quantities E-; ; , the correlation matrix of measured or even: rnxrn . . •/->/-> r* quantities, the matrix of cofactors of measured quantities =g\> v , the vector of residuals of measured unxl quantities (25) The standard deviation of unknown quantities - се The medium residuals of unknowns are the functions of standard deviations of meaurements. Unknowns can thus be denoted as the functions of measurements bearing in mind that we must take into consideration the Law of Cofactor Increment. The matrix of covariances Qf e is uxu equal to the inverse matrix of coefficients of normal equations N-1. 1 uxu For three unknowns, the matrix of covariances Qe f may be written in the form 3x3 of: The necessary cofactors, intended for the estimation ofthe accuracy ofthe unknowns, are on the main diagonal of the covariance matrix (the matrix of the cofactors of the unknowns) Qeе. The standard deviations of uxu the unknown quantities are therefore: (24) The standard deviation of levelled quantities - сгг (26) The necessary cofactors for an evaluation of accuracy of said levelled quantities are on the main diagonal of the matrix of cofactors of levelled quantities, E ' Q„„ = A Qee Ar (27) The standard deviation of residuals of measured quantities - с T vv The standard deviation of residuals of measured quantities may be gotten through the following: (28) The cofactors necessary to obtain an evaluation of the accuracy of the residuals of our measured values E , can be obtained vvu' as the difference between the cofactors of measured quantities Effi. and the cofactors of levelled quantities Em.. Determination of the main standard deviations of unknowns: During a given levelling of derisive measurements, the position of a point may be determined on the basis of certain previously measured quantities. That is how, besides levelled quantities of unknowns, č,2, čg, ..., ^ , one also obtains the covariance matrix, Eee : is obviously not much different: (29) Ч1 ■■ (Т cf "v CT vz ■* а 4 = ćr л У а : а о» 6 Чхх ч» • ■ Чт 4„ Чуу Чу, ■■ Чуй Чъ qr Ч:; " я,„ Ч» Чу* ч,и Яш, Ixx 4= - Чху Чуу-Ь Чуг ■■■ Яп ••• Чхи Чуй 4zu Чш Чуй 4«, Чш, = 0 (32) The characteristic equation then goes like this: (30) P (AM-1)M ,Au-1+...+aA+a0 ux ' v ' u-1 1 0 (33) =CJ"o Q« The elements on the main diagonal of the covariance matrix, E,, are squares of standard deviations of the determination of the position of our given point in the direction of the coordinate axis. Many times, however, it is also necessary to determine the maximum - or minimum, depending on the case - values of said deviations. The values of our main deviations (the maximum, minimum and binormal standard deviations) are determined with the aid of the selves' values of X. and their belonging selves' vectors s. of the covariance matrix г Q„. The »self values« of the covariance uxu ££ matrix, Q are obtained according to the uxu - PJ0-) being the characteristic polynomial The »zeroes« of the characteristic polynomial Pu(^) are the self values of the covariance matrix Q uxu ^ The selfvalues X., of course, have belonging self vectors denoted as s, of the covariance matrix Q^, and the latter are defined as: Q... s = X . s (34) equation: det(QÄ - XI) = 0 (31) and the equation for the determination of self values X. of the covariance matrix Q Each self value of X. provides one witha system of equations with the aid of which the afore-mentioned s . vectors may be determined. Determining the solutions of higher-degree polynomials is a very expansive and demanding practice, which is why various computer programmes have been enlisted with this very purpose in mind, aiding us in this quest to determine the previously mentioned self values and vectors. The self values of X and their belonging self vectors s of the covariance matrix г Q„ determine the quantitative values and uxu directions of our main deviations. The quantities of main standard deviations of unknowns are thus determined with the aid of the following equations: Ol _eigen =а, _ eigen и _ с igen =6, (35) К к Ъ the self values of the o0, the standard deviation ofthe levellin of the measured quantities covariance matrix Q„ 1Ш ! CC Gu eigen, the main deviation of unknowns in the direction of itselfs coordinate system plane (of a pedalloid as well as ellipoid) (37) are the equations for the determination of main deviations of the position of the point. The main standard deviations obinor, ominor, omajor represent the values of the half-axes a, b, c of the deviations' ellipsoid. The directions and quantitative values of the half-axes a, b, c of the deviations' ellipsoid may be obtained with the aid of vectors sx, as in: = D, s- =a. S- = CT Jk Jk-Jh- (38) The main standard deviations and the pedalloid (ellipsoid) of deviations The directions of mai deviation unknowns feigen ^gen, ^igen .... feigen are determined by the self vectors s.. That is how the sg. vectors, which obviously determine the directions and quantities of main standard 1 • A A A A deviations. Ci_e1gen. feigen. feigen .... °u_eigen , of unknowns, may be written down as: sc"i = ( Srf3=- » * CLE-Ti» * gìыи / * • : •' ; J ■na »._ J ии id. ! 7J-) IsiAliyf JtigP -.Hu. Vи isx»> [M1 Ouit IlillUlUo «Mtüwfi Ilirtil» i mi г m ni hm A Codelist contains a list of predefined descriptions and information (codes) that can be used to describe the surveyed features in the field. Thematical codes are point-related, and contain non-spatial information (e.g. Code: tree, Attributes: species, diameter etc.). Codes can later be interpreted by the office software to create symbols, lines and areas and speed up the whole process from field to finish. Conclusions Leica Geo Office is a programme with the aid of which the mine surveyor is able to carry out the most vital office operations (for surface and underground surveying) such as: - Optimal design of standard daily survey procedures in underground and open pit (quarry) mining including ex- tended networks for underground and surface control, subsidence observations, engineering constructions survey and control, etc. - Assessing the quality and cost of any survey activities. - Processing the observations made by staff mine surveyors. - Assessing the quality of the processed observations. - Obtaining a "terrain model" that for the time being can be created exclusively for surfaces (topographic survey of surface installations, quarry operations: drilling, blasting, production control, disposal and waste management). Povzetek Uporaba programskega paketa Leica Geo Office v jamomerstvu Programska oprema je pomembeno orodje vsakega geodeta. Leica Geosystems nudi širok nabor programskih rešitev, ki predstavljajo komplement merilnim inštrumentom in zagotavlja najvišjo produktivnost od zajema meritev na terenu do končne predstavitve podatkov. Ne glede na izbran inštrumentarij ali mersko tehniko jamomerec z njim prenaša podatke med inštrumentom in osebnim računalnikom, pripravlja terenske zapisnike in zapisnike obdelav, izvaža podatke v številne besedilne, GIS in CAD zapise, naknadno obdeluje in izravnava meritve ter nenazadnje predstavi rezultate. Zaradi modularne zasnove si lahko vsak uporabnik popolnoma prilagodi Leica Geo Office svojim potrebam. Posamezni standardni in opcijski moduli nudijo podporo tako vsakdanjim rutinskim kot tudi specifičnim merskim nalogam. Leica Geo Office predstavlja zmogljivo in celovito pisarniško okolje tudi za potrebe v jamomerstvu. Podprte so standardne vsakodnevne merske naloge tako rudnikih kot pri odprtih kopih (topografska merjenja, kontrolna merjenja, izračuni volumnov, obdelava tahimetričnih opazovanj...), vse do najzahtevnejših nalog, vključno s projektiranjem, merjenjem in obdelavo geodetskih mrež. Prav jedri za naknadno obdelavo opazovanj in 3D izravnavo sta najpomembnejša in zelo zmogljiva modula v programskem paketu. Modul PSI-Pro omogoča naknadno obdelavo GPS in GLO-NASS opazovanj s SmartCheck algoritmi, ki omogočajo najvišjo zanesljivost zaradi stalne neodvisne kontrole integritete ini-cializacije. Algoritmi omogočajo samodejno izbiro parametrov naknadne obdelave, izkušenemu uporabniku pa so na voljo številne napredne možnosti, popoln nadzor nad obdelavo ter zmogljiva orodja za predstavitev in analizo rezultatov. MOVE3 jedro za izravnavo omogoča kombinirano GPS in terestrično izravnavo opazovanj. V sodelovanju z Leico Geosystems, podjetjem Geoservis, ki je njihov avtoriziran distributer in serviser, ter Naravoslovno tehniško fakulteto, Katedro za rudarsko merjenje in geofizikalno raziskovanje je bil modul celo nadgrajen z možnostjo izpisa celotne variančno-kovariančne matrike, ki je potrebna za dodatne analize in kontrolo kvalite. References [1] Guidelines to Data Processing in SkiPro v3. Leica Geosystems, 2003. Leica Geo Office v3 Release Notes. 2005. Leica Geo Office v4 Release Notes. 2006. Leica Geo Office v5 online help. Leica Geo Office v5 Release Notes. 2006. Leica Geosystems homepage, www. leica-geosystems.com, 2007. [7] Ski-Pro v3 - GPS Data Processing, What's New. Leica Geosystems, 2003. Author's Index Balchand A.N. balchand@rediffmail.com 501 Bilban Gregor gregor.bilban@geoservis.si 545 Bombač David david.bombac@ntf.uni-lj.si 471 Brojan Miha miha.brojan@fs.uni-lj.si 471 Chandramohan T. cmohant@yahoo.com 501 Fajfar Peter peter.fajfar©ntf.uni-lj.si 471 Ganić Aleksandar aganic@rgf.bg.ac.yu 545 Kores Stanislav stanislav.kores@ntf.uni-lj.si 439 Kosel Franc franc.kosel@fs.uni-lj.si 471 Lajlar Bojan bojan.lajlar@rlv.si 513 Lamot Aleš potocnik.ognjemeti@siol.net 529 Medved Jožef jozef.medved@ntf.uni-lj.si 439, 457 Mrvar Primož primoz.mrvar@ntf.uni-lj.si 439, 457 Supovec Ivan supovec@hgem.si 513 Turk Rado rado.turk@ntf.uni-lj.si 471 Vižintin Goran goran.vizintin@ntf.uni-lj.si 513 Vončina Maja maja.voncina@ntf.uni-lj.si 439, 457 Vukelič Željko zeljko.vukelic@ntf.uni-lj.si 513 Vulić Milivoj milivoj.vulic@ntf.uni-lj.si 529, 545 Zupanič Franc franc.zupanic@uni-mb.si 457 Author's Index, Vol. 54 Anciaux Paul paul.anciaux@ec.europa.eu 345 Andjelov Mišo miso.andjelov@gov.si 235 Anžel Ivan ivan.anzel@uni-mb.si 303,319 Balchand A.N. balchand@rediffmail.com 501 Bašagić Mirza mbasagic@lol.ba 127,217 Bilban Gregor gregor.bilban@geoservis.si 545 Bombač David david.bombac@ntf.uni-lj.si 151, 471 Brecelj Uroš uros.brecelj@primorje.si 265 Breskvar Bojan bojan.breskvar@imt.si 165 Brojan Miha miha.brojan@fs.uni-lj.si 151, 471 Čarman Magda magda.carman@geo-zs.si 77 Chandramohan T. cmohant@yahoo.com 501 Dervarič Evgen evgen.dervaric@rlv.si 387 Dolenec Matej matej.dolenec@s5.net 63,189 Dolenec Tadej tadej.dolenec@ntfgeo.uni-lj.si 63 Dozet Stevo stevo.dozet@geo-zs.si 361 Durgutović Anes anes.durgutovic@oikos.si 419 Fajfar Peter peter.fajfar@ntf.uni-lj.si 1,165, 471 Fazarinc Matevž matevz.fazarinc@guest.arnes.si 1,33 Ganić Aleksandar aganic@rgf.bg.ac.yu 545 Gantar Ivan ivan.gantar@rudnik-zv.si 117 Gojič Mirko gojic@simet.hr 331 Kejžar Rajko rajko.kejzar@fs.uni-lj.si 49,179 Kejžar Uroš uros.kejzar@iskra-varjenje.si 49,179 Kneissl C. Albert kneissl@unileoben.ac.at 319 Kočevar Heda heda.kocevar@omegaconsult.si 223 Kolar-Jurkovšek Tea tea.kolar@geo-zs.si 361 Kores Stanislav stanislav.kores@ntf.uni-lj.si 287, 439 Kosec Lado kosec@ntf.uni-lj.si 179,331 Kosel Franc franc.kosel@fs.uni-lj.si 471 Kožuh Stjepan kozuh@simet.hr 331 Krkovič Matija matija.krkovic@kclj.si 151 Kugler Goran goran.kugler@ntf.uni-lj.si 1,15,33 Lajlar Bojan bojan.lajlar@rlv.si 513 Lambaša Živana 63 Lamot Aleš potocnik.ognjemeti@siol.net 529 Langer William blanger@usgs.gov 345 Langof Zlatko 127 Likar Boris boris.likar@rudnik-zv.si 117 Lojen Gorazd gorazd.lojen@uni-mb.si 319 Lojen Sonja sonja.lojen@ijs.si 63 Medved Jožef jozef.medved@ntf.uni-lj.si 303, 439, 457 Mikulič Zlatko zlatko.mikulic@gov.si 235 Miler Miloš mmiler@email.si 189 Mrvar Primož primoz.mrvar@ntf.uni-lj.si 33,303, 439, 457 Oblak Katarina katarina.oblak@ntf.uni-lj.si 203 Pavšič Jernej jernej.pavsic@ntf.uni-lj.si 189 Peruš Iztok iperus@siol.net 1,15 Petrič Mitja mitja.petric@ntf.uni-lj.si 287 Rogan Nastja nastja.rogan@ntfgeo.uni-lj.si 63 Rudolf Rebeka rebeka.rudolf@uni-mb.si 303 Savić Vlado vlado.savic@gov.si 235 Setnikar Dušan dusan.setnikar@gz-ce.si 403 Shields Deborah dshields@lamar.colostate.edu 345 Skopljak Ferid 127,217 Souvent Petra petra.souvent@gov.si 235 Stamenković Dragoslav dragstam@yubc.net 303 Sternad Željko zeljko.sternad@irgo.si 117 Supovec Ivan supovec@hgem.si 513 Šetinc Marko marko.setinc@omegaconsult.si 223 Škripić Nijaz 127,217 Šolar Slavko slavko.solar@geo-zs.si 345 Šporin Jurij jurij.sporin@irgo.si 97,117 Terčelj Milan milan.tercelj@ntf.uni-lj.si 1,15,33,165 Turk Rado rado.turk@ntf.uni-lj.si 15,33,151,165, 471 Unterweger Elfriede elfriede.unterweger@unileoben.ac.at 319 Uranjek Gregor gregor.uranjek@gmail.com 247 Večko Pirtovšek Tatjana tpirtovsek@metalravne.com 1,15 Vižintin Goran goran.vizintin@ntf.uni-lj.si 513 Vončina Maja maja.voncina@ntf.uni-lj.si 287, 439, 457 Vukelić Željko zeljko.vukelic@ntf.uni-lj.si 97,117, 513 Vulić Milivoj milivoj.vulic@ntf.uni-lj.si 247, 265,403,419, 529, 545 Yilmaz Levent lyilmaz@itu.edu.tr 87 Zalar Anton anton.zalar@ijs.si 151 Zupančič Hartner Tjaša tjasa.zupancic@zlatarnacelje.si 303 Zupanič Franc franc.zupanic@uni-mb.si 319, 457 RMZ MATERIALS AND GEOENVIRONMENT Contents Volume 54, 2007/1, 2, 3, 4 54/1 Hot forming of AISI D2 tool steel Večko Pirtovšek, T., Kugler, G., Fajfar, P., Fazarinc, M., Perus, I., Terćelj, M....................... 1 Flow stresses of the AISI A2 tool steel Večko Pirtovšek, T., Perus, I., Kugler, G., Turk, R., Terćelj, M................................................ 15 Development of test rig for thermal fatigue testing - preliminary results Fazarinc, M., Turk, R., Kugler, G., Mrvar, P., Terčelj, M......................................................... 33 Pulzno varjenje konstrukcijskih jekel Kejžar, R., Kejžar, U..................................................................................................................... 49 15N signal of Aplysina aerophoba as a tracer of anthropogenic nitrogen in the Murter Sea and Pirovac Bay (Central Adriatic) Rogan, N., Dolenec, T., Lojen, S., Lambaša, Ž., Dolenec, M....................................................... 63 Rock failures in tunnels Ćarman, M..................................................................................................................................... 77 The Solution of Differential Equations of Fluid Flow by Numerical Program Yilmaz, L........................................................................................................................................ 87 Optimization of geo-mechanical-structural drilling with diamond crowns Sporin, J., Vukelić, Ž..................................................................................................................... 97 Filling-up mine spaces of »Block 1« and »Block 2« in the Uranium mine Žirovski vrh from the surface and remediation of a damaged cementation of well for filling-up mine spaces Sporin, J., Sternad, Ž., Vukelić, Ž., Likar, B., Gantar, 1............................................................. 117 Geotechnical conditions for construction of sanitary disposal site »Lukavačka rijeka«, B&H Skripić, N., Bašagić . M., Langof, Z., Skopljak, F......................................................................... 127 Characterization of titanium and stainless steel medical implants surfaces Bombač, D., Brojan, M., Krkovič, M., Turk, R., Zalar, A........................................................ 151 Hot forming of Zn and ZnCuTi, ZnPb alloys Fajfar, P., Turk, R., Breskvar, B., Terćelj, M............................................................................. 165 RMZ-M&G 2007, 54 Varjenje močno legiranih jekel z oplaščenimi elektrodami Kejžar, R., Kosec, L., Kejžar u................................................................................................... 179 Določitev meje T/J z analizo stabilnih izotopov 613C in 618o (Krim, Slovenija) Miler, M., Pavšič, J., Dolenec, M................................................................................................ 189 Foraminiferal suborder Robertinina from the Badenian of Kozjansko (Eastern Slovenia) Oblak, К........................................................................................................................................ 203 Geological characteristics of the terrain along Vc corridor between Sava river and Sarajevo town Bašagić, M., Skripič, N., Skopljak, F............................................................................................ 217 Environmental protection and investment costs as factors of road placement Kočevar, H., Setinc, M................................................................................................................ 223 Designing a national groundwater quantity monitoring network on groundwater bodies with alluvial aquifers in Slovenia Souvent, P., Mikulič, Z., Andjelov, M., Savić, V. ........................................................................ 235 A contribution to construction monitoring with simultaneous application of various types of observations Vulić, M., Uranjek, G................................................................................................................... 247 Distance reduction with the use of uDF and Mathematica Vulić, M., Brecelj, U.................................................................................................................... 265 Characterisation of a new dental alloy with high Au content Rudolf, R., Zupančič Hartner, T., Anžel, I., Mrvar, P., Medved, J., Stamenkovič, D................. 303 Characterization of Cu-Al-Ni melt-spun ribbons using a focussed ion beam (FIB) ZuPANič, F., Unterweger, E., Kneissl, A.C., Anžel, I., Lojen, G................................................. 319 The effect of annealing on properties of AISI 316L base and weld metals Kožuh, S., Gojič, M., Kosec, L..................................................................................................... 331 Sustainability and aggregates: selected (european) issues and cases Solar, S., Shields, D., Langer, W., Anciaux, P. ........................................................................... 345 Spodnjetriasne plasti na južnovzhodnem obrobju Ljubljanske kotline, osrednja Slovenija Dozet, S., Kolar-Jurkovšek, T..................................................................................................... 361 Strategija dolgoročne proizvodnje premoga in izvedba procesa prestrukturiranja Premogovnika Velenje Dervarič, E.................................................................................................................................... 387 RMZ-M&G 2007, 54 Creating new user defined functions for 2D adjustment by parameter variation modelling Vulić, M., Setnikar, D.................................................................................................................. 403 "UDF" for volume calculation with the use of "NTF" method Vulić, M., Durgutović, A............................................................................................................. 419 Dissolution of iron in aluminium alloys Kores, s., Vončina, M., Mrvar, P., Medved, J.............................................................................. 439 The kinetics of precipitation in Al-Mg and Al-Mg-Cu alloy VoNčiNA, M., Mrvar, P., Zupanič, F., Medved, J............................................................................ 457 Review of materials in medical applications Bombač, D., Brojan, M., Fajfar, P., Kosel, F., Turk, R................................................................ 471 Regional sediment yield pattern for the west flowing rivers of Kerala state, India Chandramohan, T., Balchand, A.N.............................................................................................. 501 Technology of producing impressed filters to encompass two layers of aquifers VuKELič, Ž., Lajlar, B., Supovec, I., Vižintin, G........................................................................... 513 A realistic estimate of the accuracy of position measurements of characteristic terrain points via the RTK-GPS method Vulić, M., Lamot, a....................................................................................................................... 529 The use of Leica Geo Office in mine surveying Bilban, G., Vulić, M., Ganić, A..................................................................................................... 545 RMZ MATERIALS AND GEOENVIRONMENT Subject Index Volume 54, 2007/1, 2, 3, 4 Materials and Metallurgy Hot forming of AISI D2 tool steel Večko Pirtovšek, T., Kugler, G., Fajfar, P., Fazarinc, M., Peruš, i., Terčelj, M........................ 1 Flow stresses of the AISI A2 tool steel Večko Pirtovšek, T., Peruš, i., Kugler, G., Turk, R., Terčelj, M................................................ 15 Development of test rig for thermal fatigue testing - preliminary results Fazarinc, M., Turk, R., Kugler, G., Mrvar, P., Terčelj, M................................................... 33 Pulzno varjenje konstrukcijskih jekel Kejžar, R., Kejžar, u..................................................................................................................... 49 Characterization of titanium and stainless steel medical implants surfaces Bombač, d., Brojan, M., Krkovič, M., Turk, R., Zalar, A......................................................... 151 Hot Forming of Zn and ZnCuTi, ZnPb Alloys Fajfar, P., Turk, R., Breskvar, B., Terčelj, M.............................................................................. 165 Varjenje močno legiranih jekel z oplaščenimi elektrodami Kejžar, R., Kosec, L., Kejžar, u................................................................................................... 179 Characterisation of a new dental alloy with high Au content Rudolf, R., Zupančič Hartner, T., Anžel, i., Mrvar, P., Medved, J., Stamenković, D................. 303 Characterization of Cu-Al-Ni melt-spun ribbons using a focussed ion beam (FIB) ZuPANič, F., unterweger, E., Kneissl, A.C., Anžel, i., Lojen, G.................................................. 319 The effect of annealing on properties of AISI 316L base and weld metals Kožuh, S., Gojić, M., Kosec, L...................................................................................................... 331 Dissolution of iron in aluminium alloys Kores, s., Vončina, M., Mrvar, P., Medved, J.............................................................................. 439 The kinetics of precipitation in Al-Mg and Al-Mg-Cu alloy Vončina, M., Mrvar, P., Zupanič, F., Medved, J............................................................................ 457 Review of materials in medical applications Bombač, D., Brojan, M., Fajfar, P., Kosel, F., Turk, R................................................................ 471 Geology 15N signal of Aplysina aerophoba as a tracer of anthropogenic nitrogen in the Murter Sea and Pirovac Bay (Central Adriatic) Rogan, N., Dolenec, T., Lojen, S., Lambaša, Ž., Dolenec, M....................................................... 63 Rock failures in tunnels Carman, M..................................................................................................................................... 77 The Solution of Differential Equations of Fluid Flow by Numerical Program Yilmaz, L........................................................................................................................................ 87 Določitev meje T/J z analizo stabilnih izotopov 613C in 618o (Krim, Slovenija) Miler, M., Pavšič, J., Dolenec, M................................................................................................. 189 Foraminiferal suborder Robertinina from the Badenian of Kozjansko (Eastern Slovenia) Oblak, K......................................................................................................................................... 203 Geological characteristics of the terrain along Vc corridor between Sava river and Sarajevo town Bašagić, M., Skripič, N., skopljak, F.............................................................................................. 217 environmental protection and investment costs as factors of road placement Kočevar, H., Šetinc, M................................................................................................................. 223 Designing a national groundwater quantity monitoring network on groundwater bodies with alluvial aquifers in Slovenia SouvENT, P., Mikulič, Z., Andjelov, M., Savić, V. ......................................................................... 235 Sustainability and Aggregates: selected (european) issues and cases Solar, S., Shields, D., Langer, W., Anciaux, P. ............................................................................ 345 Spodnjetriasne plasti na južnovzhodnem obrobju Ljubljanske kotline, osrednja Slovenija Dozet, S., Kolar-Jurkovšek, T...................................................................................................... 361 Regional sediment yield pattern for the west flowing rivers of Kerala state, India Chandramohan, T., Balchand, A.N.............................................................................................. 501 optimization of geo-mechanical-structural drilling with diamond crowns Sporin, J., Vukelić, Ž..................................................................................................................... 97 Filling-up mine spaces of »Block 1« and »Block 2« in the Uranium mine Žirovski vrh from the surface and remediation of a damaged cementation of well for filling-up mine spaces Sporin, J., Sternad, Ž., Vukelić, Ž., Likar, B., Gantar, 1............................................................. 117 RMZ-M&G 2007, 54 Geotechnical conditions for construction of sanitary disposal site »Lukavačka rijeka«, B&H Skripič, N., Bašagić . M., Langof, Z., Skopljak, F......................................................................... 127 A contribution to construction monitoring with simultaneous application of various types of observations Vulić, M., Шашек, G.................................................................................................................... 247 Distance reduction with the use of uDF and Mathematica Vulić, M., Brecelj, u..................................................................................................................... 265 Strategija dolgoročne proizvodnje premoga in izvedba procesa prestrukturiranja Premogovnika Velenje Dervarič , E..................................................................................................................................... 387 Creating new user defined functions for 2D adjustment by parameter variation modelling Vulić , M., Setnikar, D................................................................................................................... 403 "UDF" for volume calculation with the use of "NTF" method Vulić, M., Durgutović, a.............................................................................................................. 419 Technology of producing impressed filters to encompass two layers of aquifers Vukelič , Ž., Lajlar , B., Supovec, I., Vižintin, G........................................................................... 513 A realistic estimate of the accuracy of position measurements of characteristic terrain points via the RTK-GPS method Vulić, M., Lamot, A....................................................................................................................... 529 The Use of Leica Geo Office in Mine Surveying Bilban, G., Vulić, M., Ganić, A..................................................................................................... 545 INSTRUCTIONS TO AUTHORS RMZ-MATERIALS & GEOENVIRONMENT (RMZ- Materiali in geookolje) is a periodical publication with four issues per year (established 1952 and renamed to RMZ-M&G in 1998). The main topics of contents are Mining and Geotechnology, Metallurgy and Materials, Geology and Geoenvironment. RMZ-M&G publishes original Scientific articles, Review papers, Technical and Expert contributions (also as short papers or letters) in English. In addition, evaluations of other publications (books, monographs,...), short letters and comments are welcome. A short summary of the contents in Slovene will be included at the end of each paper. It can be included by the author(s) or will be provided by the referee or the Editorial Office. * Additional information and remarks for Slovenian authors: English version with extended »Povzetek«, and additional roles (in Template for Slovenian authors) can be written. Only exceptionally the articles in the Slovenian language with summary in English will be published. The contributions in English will be considered with priority over those in the Slovenian language in the review process. Authorship and originality of the contributions. Authors are responsible for originality of presented data, ideas and conclusions as well as for correct citation of data adopted from other sources. The publication in RMZ-M&G obligate authors that the article will not be published anywhere else in the same form. Specification of Contributions Optimal number of pages of full papers is 7 to 15, longer articles should be discussed with Editor, but 20 pages is limit. Scientific papers represent unpublished results of original research. Review papers summarize previously published scientific, research and/or expertise articles on the new scientific level and can contain also other cited sources, which are not mainly result of author(s). Technical and Expert papers are the result of technological research achievements, application research results and information about achievements in practice and industry. Short papers (Letters) are the contributions that contain mostly very new short reports of advanced investigation. They should be approximately 2 pages long but should not exceed 4 pages. Evaluations or critics contain author's opinion on new published books, monographs, textbooks, exhibitions...(up to 2 pages, figure of cover page is expected). In memoriam (up to 2 pages, a photo is expected). Professional remarks (Comments) cannot exceed 1 page, and only professional disagreements can be discussed. Normally the source author(s) reply the remarks in the same issue. Supervision and review of manuscripts. All manuscripts will be supervised. The referees evaluate manuscripts and can ask authors to change particular segments, and propose to the Editor the acceptability of submitted articles. Authors can suggest the referee but Editor has a right to choose another. The name of the referee remains anonymous. The technical corrections will be done too and authors can be asked to correct missing items. The final decision whether the manuscript will be published is made by the Editor in Chief. The Form of the Manuscript The manuscript should be submitted as a complete hard copy including figures and tables. The figures should also be enclosed separately, both charts and photos in the original version. In addition, all material should also be provided in electronic form on a diskette or a CD. The necessary information can conveniently also be delivered by E-mail. Composition of manuscript is defined in the attached Template The original file of Template is temporarily available on E-mail addresses: peter.fajfar@ntf.uni-lj.si, barbara.bohar@ntf.uni-lj.si References - can be arranged in two ways: - first possibility: alphabetic arrangement of first authors - in text: (Borgne, 1955), or - second possibility: [1] numerated in the same order as cited in the text: example[1] Format of papers in journals: Le Borgne, E. (1955): Susceptibilite magnetic anomale du sol superficiel. Annales de Geophysique, 11, pp. 399-419. Format of books: Roberts, J. L. (1989): Geological structures, MacMillan, London, 250 p. Text on the hard print copy can be prepared with any text-processor. The electronic version on the diskette, CD or E-mail transfer should be in MS Word or ASCII format. Captions of figures and tables should be enclosed separately. Figures (graphs and photos) and tables should be original and sent separately in addition to text. They can be prepared on paper or computer designed (MSExcel, Corel, Acad). Format. Electronic figures are recommended to be in CDR, Al, EPS, TIF or JPG formats. Resolution of bitmap graphics (TIF, JPG) should be at least 300 dpi. Text in vector graphics (CDR, Al, EPS) must be in MSWord Times typography or converted in curves. Color prints. Authors will be charged for color prints of figures and photos. Labeling of the additionally provided material for the manuscript should be very clear and must contain at least the lead author's name, address, the beginning of the title and the date of delivery of the manuscript. In case of an E-mail transfer the exact message with above asked data must accompany the attachment with the file containing the manuscript. Information about RMZ-M&G: Editor in Chief prof. dr. Peter Fajfar (tel. ++386 1 4250-316) or Secretary Barbara Bohar Bobnar, un. dipl. ing. geol. (++386 1 4704-630), Aškerčeva 12, Ljubljana, Slovenia or at E-mail addresses: peter.fajfar@ntf.uni-lj.si, barbara.bohar@ntfgeo.uni-lj.si Sending of manuscripts. Manuscripts can be sent by mail to the Editorial Office address: • RMZ-Materials & Geoenvironment Aškerčeva 12, 1000 Ljubljana, Slovenia or delivered to: • Reception of the Faculty of Natural Science and Engineering (for RMZ-M&G) Aškerčeva 12, 1000 Ljubljana, Slovenia • E-mail - addresses of Editor and Secretary • You can also contact them on their phone numbers. TEMPLATE The title of the manuscript should be written in bold letters (Times New Roman, 14, Center) Name Surname 1, .... , & Name Surname x (Times New Roman, 12, Center) XFaculty of ... , University of ... , Address., Country, e-mail: ... (Times New Roman, 11, Center) THE LENGTH OF FULL PAPER SHOULD NOT EXCEED TWENTY (20, INCLUDING FIGURES AND TABLES) PAGES (OPTIMAL 7 TO 15), SHORT PAPER FOUR (4) AND OTHER TWO (2) WITHOUT TEXT FLOWING BY GRAPHICS AND TABLES. Abstract (Times New Roman, Normal, 11): The text of the abstract is placed here. The abstract should be concise and should present the aim of the work, essential results and conclusion. It should be typed in font size 11, single-spaced. Except for the first line, the text should be indented from the left margin by 10 mm. The length should not exceed fifteen (15) lines (10 are recommended). Key words: a list of up to 5 key words (3 to 5) that will be useful for indexing or searching. Use the same styling as for abstract. Introduction (Times New Roman, Bold, 12) Two lines below the keywords begin the introduction. Use Times New Roman, font size 12, Justify alignment. There are two (2) admissible methods of citing references in text: 1. by stating the first author and the year of publication of the reference in the parenthesis at the appropriate place in the text and arranging the reference list in the alphabetic order of first authors; e.g.: "Detailed information about geohistorical development of this zone can be found in: Antonijević (1957), Grubić (1962), ..." "... the method was described previously (Hoefs, 1996)" 2. by consecutive Arabic numerals in square brackets, superscripted at the appropriate place in the text and arranging the reference list at the end of the text in the like manner; e.g.: "... while the portal was made in Zope[3] environment." Materials and methods (Times New Roman, Bold, 12) This section describes the available data and procedure of work and therefore provides enough information to allow the interpretation of the results, obtained by the used methods. Results and discussion (Times New Roman, Bold, 12) Tables, figures, pictures, and schemes should be incorporated in the text at the appropriate place and should fit on one page. Break larger schemes and tables into smaller parts to prevent extending over more than one page. Conclusions (Times New Roman, Bold, 12) This paragraph summarizes the results and draws conclusions. Acknowledgements (Times New Roman, Bold, 12, Center - optional) This work was supported by the ****. References (Times New Roman, Bold, 12) In regard to the method used in the text, the styling, punctuation and capitalization should conform to the following: FIRST OPTION - in alphabetical order Casati, P., Jadoul, F., Nicora, A., Marinelli, M., Fantini-Sestini, N. & Fois, E. (1981): Geologia della Valle del'Anisici e dei gruppi M. Popera - Tre Cime di Lavaredo (Dolomiti Orientali). Riv. Ital. Paleont.; Vol. 87, No. 3, pp. 391-400, Milano. Folk, R. L. (1959): Practical petrographic classification of limestones. Amer. Ass. Petrol. Geol. Bull.; Vol. 43, No. 1, pp. 1-38, Tulsa. SECOND OPTION - in numerical order [1] Trček, B. (2001): Solute transport monitoring in the unsaturated zone of the karst aquifer by natural tracers. Ph.D. Thesis. Ljubljana: University of Ljubljana 2001; 125 p. [2] Higashitani, K., Iseri, H., Okuhara, K., Hatade, S. (1995): Magnetic Effects on Zeta Potential and Diffusivity of Nonmagnetic Particles. Journal of Colloid and Interface Science 172, pp. 383-388. Citing the Internet site: CASREACT-Chemical reactions database [online]. Chemical Abstracts Service, 2000, updated 2.2.2000 [cited 3.2.2000]. Accessible on Internet: http://www.cas. org/CASFILES/casreact.html. Povzetek (Times New Roman, 12) A short summary of the contents in Slovene (up to 400 characters) can be written by the author(s) or will be provided by the referee or by the Editorial Board. TEMPLATE for Slovenian Authors The title of the manuscript should be written in bold letters (Times New Roman, 14, Center) Naslov članka (Times New Roman, 14, Center) Name Surname ... , & Name Surnamex (Times New Roman , 12, Center) Ime Priimek 1, Ime Priimekx (Times New Roman , 12, Center) XFaculty of ... , University of ... , Address., Country; e-mail: ... (Times New Roman, 11, Center) XFakulteta..., Univerza., Naslov., Država; e-mail: ... (Times New Roman, 11, Center) THE LENGTH OF ORIGINAL SCIENTIFIC PAPER SHOULD NOT EXCEED TWENTY (20, INCLUDING FIGURES AND TABLES) PAGES (OPTIMAL 7 TO 15), SHORT PAPER FOUR (4) AND OTHER TWO (2) WITHOUT TEXT FLOWING BY GRAPHICS AND TABLES. DOLŽINA IZVIRNEGA ZNANSTVENEGA ČLANKA NE SME PRESEGATI DVAJSET (20, VKLJUČNO S SLIKAMI IN TABELAMI), KRATKEGA ČLANKA ŠTIRI (4) IN OSTALIH PRISPEVKOV DVE (2) STRANI. Abstract (Times New Roman, Normal, 11): The text of the abstract is placed here. The abstract should be concise and should present the aim of the work, essential results and conclusion. It should be typed in font size 11, single-spaced. Except for the first line, the text should be indented from the left margin by 10 mm. The length should not exceed fifteen (15) lines (10 are recommended). Izvleček (TNR, N, 11): Kratek izvleček namena članka ter ključnih rezultatov in ugotovitev. Razen prve vrstice naj bo tekst zamaknjen z levega roba za 10 mm. Dolžina naj ne presega petnajst (15) vrstic (10 je priporočeno). Key words: a list of up to 5 key words (3 to 5) that will be useful for indexing or searching. Use the same styling as for abstract. Ključne besede: seznam največ 5 ključnih besed (3-5) za pomoč pri indeksiranju ali iskanju. Uporabite enako obliko kot za izvleček. Introduction - Uvod (Times New Roman , Bold , 12) Two lines below the keywords begin the introduction. Use Times New Roman, font size 12, Justify alignment. All captions of text and tables as well as the text in graphics must be prepared in English and Slovenian language. Dve vrstici pod ključnimi besedami se začne Uvod. Uporabite pisavo TNR, velikost črk 12, z obojestransko poravnavo. Naslovi slik in tabel (vključno z besedilom v slikah) morajo biti pripravljeni v slovenskem in angleškem jeziku. Figure (Table) X. Text belonging to figure (table) Slika (Tabela) X. Pripadajoče besedilo k sliki (tabeli) There are two (2) admissible methods of citing references - obstajata dve sprejemljivi metodi navajanja referenc: 1. by stating the first author and the year of publication of the reference in the parenthesis at the appropriate place in the text and arranging the reference list in the alphabetic order of first authors; e.g.: 1. z navedbo prvega avtorja in letnice objave reference v oklepaju na ustreznem mestu v tekstu in z ureditvijo seznama referenc po abecednem zaporedju prvih avtorjev; npr.: "Detailed information about geohistorical development of this zone can be found in: Antonijević (1957), Grubić (1962), ..." "... the method was described previously (Hoefs, 1996)" or/ali 2. by consecutive Arabic numerals in square brackets, superscripted at the appropriate place in the text and arranging the reference list at the end of the text in the like manner; e.g.: 2. z zaporednimi arabskimi številkami v oglatih oklepajih na ustreznem mestu v tekstu in z ureditvijo seznama referenc v številčnem zaporedju navajanja; npr.; "... while the portal was made in Zope[3] environment." Materials and methods (Times New Roman , Bold , 12) This section describes the available data and procedure of work and therefore provides enough information to allow the interpretation of the results, obtained by the used methods. Ta del opisuje razpoložljive podatke, metode in način dela ter omogoča zadostno količino informacij, da lahko z opisanimi metodami delo ponovimo. Results and discussion - Rezultati in razprava (Times New Roman, Bold, 12) Tables, figures, pictures, and schemes should be incorporated (inserted, not pasted) in the text at the appropriate place and should fit on one page. Break larger schemes and tables into smaller parts to prevent extending over more than one page. Tabele, sheme in slike je potrebno vnesti (z ukazom Insert, ne Paste) v tekst na ustreznem mestu. Večje sheme in tabele je potrebno ločiti na manjše dele, da ne presegajo ene strani. Conclusions - Sklepi (Times New Roman , Bold , 12) This paragraph summarizes the results and draws conclusions. Povzetek rezultatov in zaključki. Acknowledgements - Zahvale (Times New Roman, Bold, 12, Center -optional) This work was supported by the........... Izvedbo tega dela je omogočilo......... References - Viri (Times New Roman , Bold , 12) With regard to the method used in the text, the styling, punctuation and capitalization should conform to the following: Glede na uporabljeno metodo citiranja referenc v tekstu upoštevajte eno od naslednjih oblik: FIRST OPTION (recommended) - PRVA MOŽNOST (priporočena) - in alphabetical order (v abecednem zaporedju) Casati, P., Jadoul, F., Nicora, A., Marinelli, M., Fantini-Sestini, N. & Fois, E. (1981): Geologia della Valle del'Anisici e dei gruppi M. Popera - Tre Cime di Lavaredo (Dolomiti Orientali). Riv. Ital. Paleont.; Vol. 87, No. 3, pp. 391-400, Milano. Folk, R. L. (1959): Practical petrographic classification of limestones. Amer. Ass. Petrol. Geol. Bull.; Vol. 43, No. 1, pp. 1-38, Tulsa. SECOND OPTION - DRUGA MOŽNOST - in numerical order (v numeričnem zaporedju) [1] Trček, B. (2001): Solute transport monitoring in the unsaturated zone of the karst aquifer by natural tracers. Ph.D. Thesis. Ljubljana: University of Ljubljana 2001; 125 p. [2] Higashitani, K., Iseri, H., Okuhara, K., Hatade, S. (1995): Magnetic Effects on Zeta Potential and Diffusivity of Nonmagnetic Particles. Journal of Colloid and Interface Science 172, pp. 383-388. Citing the Internet site: CASREACT-Chemical reactions database [online]. Chemical Abstracts Service, 2000, updated 2.2.2000 [cited 3.2.2000]. Accessible on Internet: http://www.cas. org/CASFILES/casreact.html. Citiranje Internetne strani: CASREACT-Chemical reactions database [online]. Chemical Abstracts Service, 2000, obnovljeno 2.2.2000 [citirano 3.2.2000]. Dostopno na svetovnem spletu: http://www.cas.org/CASFILES/casreact.html. Povzetek - Summary (Times New Roman, 12) An extended summary of the contents in Slovene (from one page to approximately 1/3 of the original article length). Razširjeni povzetek vsebine prispevka v Angleščini (od ene strani do približno 1/3 dolžine izvirnega članka). No. of indexing of RMZ-M&G in singular Databases v (Število indeksiranih člankov iz RMZ-M&G v posameznih bazah) (prepared by Fajfar, P. - from search done by Sercelj, M., CTK Ljubljana, 15.2.2007) DATABASE NAME HITS 1: Civil Engineering Abstracts 773 2: CA SEARCH® - Chemical Abstracts® (1967- present) 760 3: Inside Conferences 313 4: Materials Business File 253 5: METADEX® 164 6: ANTE: Abstracts in New Technologies and Engineering 158 7: GeoRef 154 8: Aluminium Industry Abstracts 36 9: PASCAL 30 10: Energy Science and Technology 27 11: TEME - Technology and Management 27 12: Ei Compendex® 13 13: CSA Aerospace & High Technology Database 12 14: Computer and Information Systems 10 15: Mechanical & Transportation Engineering Abstracts 8 16: Engineered Materials Abstracts® 3 17: Corrosion Abstracts 3 18: Analytical Abstracts 1 19: FLUIDEX 1 20: Solid State and Superconductivity Abstracts 1 21: Electronics and Communications Abstracts 1 2748 / TOI tlezanka с. 3 3220 ihre Slovenija wutw.shre-sieel.si Rešitve za opazovanje premikov in deformacij CNSS senzor Leica GMX902 GG GPS senzor Leica GMX901 in 360° reflektor Leica GZR122 Nagibni senzor Leica NIVEL200 Samodejni tahimeter Leica TCA1201M Ш ■ -i .r- i"^ ••••- Programska oprema Leica GNSS Spider Programska oprema Leica GeoMoS servis I Authorized Leica Geosystems Distributor when it has to be right Geoservis, d.0.0. Litijska cesta 45,1000 LJubljana t. (01] 586 38 30, i. www.geoservis.si Geosystems prof. dr. Andrej Paulin Tehniški metalurški slovar (cd-romza windows) slovensko - angleško - nemški Technical metallurgical dictionary (cd-rom for windows) Slovenian - English - German Več kot 10.000 gesel s področij: - metalurgije, - tehniških materialov, - tehnike površin, - analiznih metod, - strojništva, - kemije, - elektrotehnike, - ekologije, - standardizacije, - predpisov, - ekonomike in - uporabe računalništva pri tehnoloških postopkih. Osnovne značilnosti oz. prednosti elektronske različice slovarja so preprost in izjemno hiter dostop do iskanega gesla, besede ali zveze, tudi pri zahtevnejših pogojih, ter velika prilagodljivost vmesnika uporabnikovim potrebam in željam. Slovar uporablja pregledovalnik ASP32 in je združljiv s številnimi drugimi slovarji v tem sistemu. Cenik elektronskega slovarja: Enouporabniška lokalna verzija - 58,00 EUR 5 licenc mrežna verzija - 390,00 EUR 10 licenc mrežna verzija - 535,00 EUR 20 licenc mrežna verzija - 680,00 EUR 30 licenc mrežna verzija - 825,00 EUR 40 licenc mrežna verzija - 970,00 EUR 50 licenc mrežna verzija -1.115,00 EUR Leto izdaje: 2007 Issued in 2007 Prices for the electronic dictionary: Single user local version - 58,00 EUR 5 users network version - 390,00 EUR 10 users network version - 535,00 EUR 20 users network version - 680,00 EUR 30 users network version - 825,00 EUR 40 users network version - 970,00 EUR 50 users network version -1.115,00 EUR More than 10 000 technical terms on: -metallurgy -technical materials -surface engineering -analytical methods -mechanical engineering -chemical engineering -electrical engineering -environmental engineering -standardization -technical regulations -economics, and -computer engineering in technological processes Basic characteristics or advantages, respectively, of electronic version of the dictionary is simple and very fast access to sought term, word or to complex term, also in more demanding conditions, and a great adaptability of the interface to user's needs and wishes. The dictionary uses ASP32 search system that is compatible to numerous other dictionaries in this system. Za naročila in dodatne informacijenas kontaktirajte preko e-pošte: nmmlfiìntf uni-li с/ For orders and additional information please contact us by e-mail: ™ uni-lj.si