209 Acta Chim. Slov. 1998, Y5(3), pp. 209-216 (Received 15. 5.1998) A SILVER/SILVER SULPHIDE SELECTIVE ELECTRODE PREPARED BY MEANS OF CHEMICAL TREATMENT OF SILVER WIRE D.Dobčnik, LGros and M.Kolar Faculty of Chemistry and Chemical Engineering, University of Maribor, Slovenia Summary. The preparation and usability of a sulphide ion selective electrode, prepared by means of chemical pretreatment of silver wire with an ammonium perdisulphate solution, and the sulphidization in an alkaline sulphide solution are described. The electrode is suitable for direct potentiometric measuring of sulphide in alkaline solutions of concentrations down to 1 x 10-6 mol/L. The 45 min required for each chemical treatment are enough for the preparation of the described electrode. INTRODUCTION Ag/Ag2S electrodes are prepared by means of anodic polarization of a silver rod in a solution of sodium sulphide [1], by dipping the platinum spiral, coated with porous silver, into a solution of hydrogen sulphide [2], by sulphidizing the silver wire with sulphur vapor in nitrogenous atmosphere [3] as well as by sulphidizing with cooper-alloyed silver wire in a saturated alkaline solution of sodium sulphide [4]. The authors state that even after six days of chemical treatment no black sulphide layer was observed on the surface of a pure silver wire (99.99%) which suggests that the silver sulphide layer is probably produced through an anodic reaction of a localized corrosion process [4]. 210 The preparation conditions and the performance of a small size Ag/Ag2S selective electrode are described. The analytical behaviour of this electrode, produced by chemical treatment of a silver wire, is described in terms of potential-concentration curves, electrode selectivity and titration procedures. A series of electrodes have been prepared and investigated. Their response and selectivity to Ag+ and S2- were measured and compared with those of a commercial Orion silver/sulphide electrode. Several titrations were performed to evaluate the performances of the electrode. The investigated electrode was found as a good substitute for the commercial silver/sulphide electrode in a wide variety of practical analytical systems. A simple preparation by means of chemical pre-treatment of a silver wire with an ammonium perdisuphate solution and sulphidization in alkaline sulphide solution were performed. The electrode has proven to be suitable for direct potentiometric measuring of sulphide in alkali solutions of concentrations down to 1x10-6 mol/l. The 45-min required for chemical treatments are enough for the preparation of the described electrodes. EXPERIMENTAL Reagents All the chemicals used were of the analytical grade and all the solutions were prepared in doubly distilled water. A SAOB [5] solution was prepared by dissolving 2 moles of NaOH, 0.2 moles of ascorbic acid and 0.2 moles of Na2EDTA in water and diluting them to a final volume of 1000 mL. Standard silver solutions were prepared from a stock solution (0.1 mol Ag+/L) by sequential dilution with 0.1 mol/L KNO3. A stock solution of Na2S was prepared by dissolving the reagent grade Na2Sx9H2O in 25%(v/v) SAOB [5]. It was standardized iodometrically by titration with a Na2S2O3 solution. Standard solutions were prepared from a stock solution by sequential dilution with 25%(v/v) SAOB. 211 Preparation of electrodes The pure silver wire (99.99% Ag) between 0.8 and 1.0 mm in diameter was connected with a cooper wire and adhered into a glass tube with epoxy resin. The free Ag-wire should be 10 to 15 mm long. The wire is furtheron treated in HNO3 (1+1) for approximately 10 s and thoroughly washed with doubly distilled water; then was immersed into a 0.1 mol/L solution of (NH4)2S2O8 for 15 min. After being washed with the doubly distilled water, the electrode was sulphidized in a 0.1 mol/L alkaline solution of Na2S for 30 min. Finally the electrode was thoroughly washed with doubly distilled water. Apparatus All potentiometric measurments on sulphide electrodes were performed with a digital mV/pH meter ISKRA MA 5730. The ISKRA saturated calomel electrode (SCE) with 0.1 mol/L KNO3 salt bridge was used as a standard reference elektrode. Comparative measurments were made with ORION 94-16 sulphide electrode. All measurments were carried out at 298 ± 0.1 K. RESULTS AND DISCUSSION Surface analysis The depth-profile diagram obtained by the Auger electron spectrometer (PHI SAM model 545 A) shows a quantitative elemental composition of atomic layers on the surface of the silver wire. As can be seen from Fig.1, the stoichometric composition of Ag2S is found only in the first atomic layers on the surface of the silver wire. The broadening of the concentration profile is typical of the rough surface of the chemically etched metal surface [6, 7]. 212 Available in printed version only Figure 1. The AES composition-depth profile of a sulphidized silver wire obtained by sputtering with 1 keV Ar+ ions at a 470 incidence angle and a raster size of 10 mm x 10 mm. Potentiometric behaviour Response of the silver/silver sulphide wire electrode to Ag+ and S2- ions The equilibrium potentials observed during the serial dilution of 0.1 mol/L silver nitrate in the measuring cell were plotted against logCAg+. A linear response with a slope of 58.8 mV per concentration decade (59.1 mV/decade for a theoretical Nernstian response) was obtained in the concentration range from 10-1 to less than 10-5 mol/L, followed by a non linear region at lower concentrations (Fig. 2). The same procedure was used for the sulphide ion response plot in an alkaline SAOB solution containing ascorbic acid. A linear response for E vs. logCS2- over the range from 0.1 to nearly 10-6 mol/L with the slope of 28.1 mV per concentration decade (29.55 mV/decade theoretical) was recorded as shown in Figure 3. A deviation from linear behaviour was observed in the concentration range from 10-6 to 10-7 mol/L. 213 ouu - < 500 - >^ 400 - U VI > 300 -> E •—.. W 200 - " •¦ 100 - 0 - -------1-------1-------1------ H-------1-------1-------1 -logCAg+ Figure 2. Response of the silver / silver sulphide electrode to the silver ion concentrations in 0.1 mol/L KNO3 OUU -| * -600 t .* U VI t > -700 -> S ^^ -800 ^^^^ < >•'' -900 -------1-------1-------1-------1-------1-------1-------1 -logCS2 Figure 3. Response of the silver / silver sulphide electrode to the sulphide ion concentrations in 25% (v/v) S AOB 214 The extrapolated intercepts at logCAg+ and logCS2- = 0 in Figures 2 and 3 give us the values KAg+ = 553.7 mV and Ks2- = -852.8 mV vs. SCE. Using this data and considering the potential of SCE (242.0 mV) two expressions that correlate the potential and the concentration of measuring ion can be written: Es2- = -610.8 - 28.1 logCS2-EAg+ = +795.7 + 58.8 logCAg+ The effects of several anions, namely Cl-, Br-, SCN-, I-, NO3-, S2O32-, SO42- and C2O42- on the sulphide potential response of the electrode were tested by using the mixed solution technique [8] with a constant level of sulphide concentration 1x10-5 mol/L and increasing concentrations of anions in the range between 10-1 and 10-6 mol/L. The anions have no influence in this concentration region on the measurement of sulphide. The results show that the investigated electrode can be used for selective analytical measurements in a wide variety of practical systems. Potentiometric titrations The wire electrode was also tested as an end-point indicator electrode in potentiometric titrations involving Ag+ or S2- ions. For comparison, the titrations were followed simultaneously with home made Ag/Ag2S electrodes and commercial silver/sulphide electrodes. The shape of the potentiometric titrations of Ag+ ions and the actual potential values close to and beyond the end points were in excellent agreement. Also, the comparison of the potentiometric titration of sulphide with Pb2+ in alkaline solution indicates that the titration curve and end point observed coincide to a satisfactory degree (Fig. 4, 5, 6, 7) throughout some differences in potential between both electrodes. 215 500 300 100 -- ü -100 > ~ -300 4- -500 -- -700 -- -900 0 2 4 6 8 10 12 14 VS2 /mL Figure 4. Ag titration with 0. : ,2- mol/LS 500 -r 400 -- 300 w u oc > 200 100 -- 0 -- -100 \ 0 2 4 6 8 10 12 14 VSCN/mL Figure 6. Ag titration with 0.1 mol/L SCN" 500 400 - g 300 ri > > 200 100 0 2 4 6 8 10 12 14 VCl/mL Figure 5. Ag titration with 0.1 mol/L CI" -200 j -300 - -400 ^ -500 - -600 -700 -800 -900 0 2 4 6 8 10 12 14 VPb2+/mL Figure 7. Sulphide titration in alkaline solution with 0.1 mol/L Pb2+ 216 REFERENCES [1] L.T. Abfalt, D. Jagner, Anal Chim Acta 1971, 56, 477. [2] D. J. G. Ives, G.J. Janz, Reference electrodes; Academic Press, New York 1961, p. 382 [3] R.E. Van de Laast, Analyst 1977, 102, 509. [4] Nj. Radić, K. J. Mulligan, Jr. H. B. Marc, Anal Chem 1984, 56, 297. [5] Instruction Manual; Sulphide ion electrode, silver ion electrode model 94-16; ORION Research Inc., Cambridge, Mass, 1977. [6] A. Zalar, S. Hofmann, Nucl Instr Meth Phys Res 1987, B 18, 655. [7] A. Zalar, S. Hofmann, Vaccum 1987, 37, 169. [8] E. Pungor, K. Toth, Anal Chim Acta 1969, 47, 291. Povzetek: Opisujemo pripravo sulfidne ionoselektivne elektrode s kemijsko obdelavo srebrne žice v amonijevem peroksodisulfatu in v alkalni sulfidni raztopini. Elektroda omogoča direktne potenciometrične meritve koncentracij sulfidnih ionov v alkalnih raztopinah navzdol do 10-6 mol/L. Priprava elektrode je enostavna in hitra.